Panasonic WJ-GXE900 사용자 설명서
12
q Ethernet Port (100BASE -TX) (RJ-45)
Connect an Ethernet cable to connect to a network.
Use a category 5 cable (100BASE-TX).
LINK1 Indicator: This indicator lights up when the
Use a category 5 cable (100BASE-TX).
LINK1 Indicator: This indicator lights up when the
encoder is linked to a network through this port.
SPEED Indicator: This indicator lights up when
connection (100BASE-TX) is established.
ACT Indicator: This indicator lights up when
receiving or sending data through this port.
w RS-485 Port (RS-485) (RJ-11)
Connect a device with RS-485 interface. Termination
can be set by the TERM switch (TERM).
can be set by the TERM switch (TERM).
e Trigger Output Terminal (TRIGGER OUT 1 - 4, G
(GND))
The trigger output signal (Open collector output, 25 V
DC, 50 mA max.) will be supplied from this terminal
using the contact output controlling CGI commands.
(Refer to the operating instructions (pdf file) included
on the supplied CD-ROM about the contact output
controlling CGI commands.)
The trigger output signal (Open collector output, 25 V
DC, 50 mA max.) will be supplied from this terminal
using the contact output controlling CGI commands.
(Refer to the operating instructions (pdf file) included
on the supplied CD-ROM about the contact output
controlling CGI commands.)
r Alarm Input Terminal (ALARM IN 1 - 4,
G (GND))
Connect an external device such as a sensor.
(Open collector or dry contact, low active less than
0.2 V, pulse width more than100 ms, voltage
endurance 5 V DC max.)
Connect an external device such as a sensor.
(Open collector or dry contact, low active less than
0.2 V, pulse width more than100 ms, voltage
endurance 5 V DC max.)
t Reset Input Terminal (RESET)
Use this terminal to restart the encoder.
y Cooling Fan
There is a built-in cooling fan inside of the encoder.
Do not block the ventilation openings.
Note: The cooling fan is perishable. It will need to be
Do not block the ventilation openings.
Note: The cooling fan is perishable. It will need to be
replaced it after around 30 000 hours of
operation. Replacement costs of the cooling fan
are not covered by the warranty even if it needs
to be done within the warranty period. Consult
your dealer for servicing.
operation. Replacement costs of the cooling fan
are not covered by the warranty even if it needs
to be done within the warranty period. Consult
your dealer for servicing.
u POWER Switch
Press this switch to turn the power on or off. When
the power is on, the OPERATE indicator on the front
panel will be lit.
the power is on, the OPERATE indicator on the front
panel will be lit.
i Video Input Connectors (VIDEO IN 1 - 4)
(1 V[p-p]/75Ω, NTSC composite video signal,
BNC)
Up to 4 cameras can be connected.
BNC)
Up to 4 cameras can be connected.
o Video Output Connector (VIDEO OUT)
(1 V[p-p]/75Ω, NTSC composite video signal,
9-pin D-sub)
Video signal will be looped through from the VIDEO
IN 1 - 4 respectively. Up to 4 monitors can be
connected to monitor pictures from the cameras
connected to the VIDEO IN 1 - 4. To connect
monitors, a cable (WV-CA64, not supplied) is
required.
IN 1 - 4 respectively. Up to 4 monitors can be
connected to monitor pictures from the cameras
connected to the VIDEO IN 1 - 4. To connect
monitors, a cable (WV-CA64, not supplied) is
required.
POWER
ON
OFF
SIGNAL
AUDIO IN
VIDEO OUT
VIDEO IN
100BASE-TX
RS-485
TERM
1
GND
2
3
ON OFF
4
i
q
w e rt
y
u
o
!0
!1 !2
ALARM IN
TRIGGER OUT
RESET
4 3 2 1 G 4 3 2 1 GG V + – G
MPEG2 Encoder Rear Panel
LINK1 Indicator
SPEED Indicator
ACT Indicator
GND
TB
TA
RB
RA
GND
1
2
3
4
5
6
Transmit
Receive
ON OFF
TERM
RS-485
5
4
4
RA
RB
RB
Receive
3
2
2
TA
TB
Transmit
WJ-GXE900
Signal
To the connected
device
device
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS