Panasonic WJ-GXE900 사용자 설명서
22
Unicast Transmission
The unicast transmission will be suitable for the following system.
• When it is necessary to monitor pictures from a specific camera on a specific monitor
System Example
When using the unicast transmission, the number of cameras and monitors should be same. The unicast transmission
is useful in preventing from heavy traffic in the network, not only for this system but also the other systems.
For the unicast transmission, perform the settings of "DESTINATION IP ADDRESS" and "DESTINATION PORT No." on
the VIDEO page of the encoder.
Then, it is also necessary to perform the settings of the VIDEO page of the decoder as shown below.
is useful in preventing from heavy traffic in the network, not only for this system but also the other systems.
For the unicast transmission, perform the settings of "DESTINATION IP ADDRESS" and "DESTINATION PORT No." on
the VIDEO page of the encoder.
Then, it is also necessary to perform the settings of the VIDEO page of the decoder as shown below.
DESTINATION IP ADDRESS: The same IP address entered for "DESTINATION IP ADDRESS" on the VIDEO page
of the encoder
DESTINATION PORT No.: The same port number entered for "DESTINATION PORT No." on the VIDEO page of
the encoder
OPERATE
STATUS
MPEG2 Encoder WJ-GXE
900
1
2
3
4
5
6
7
8
OPERATE
1
ACT
1000
100
LINK1
STATUS
2
3
4
5
6
7
8
MPEG2 Decoder WJ-GXD
900
PC
VIDEO IN
VIDEO OUT
MPEG2
Encoder
Encoder
MPEG2 Decoder
100BASE-TX
100BASE-TX/
1000BASE-T
1000BASE-T
10BASE-T/
100BASE-TX
100BASE-TX
Switching hub
(100Mbps/1000Mbps compatible)
(100Mbps/1000Mbps compatible)
Monitor 1
Monitor 2
Monitor 3
Monitor 4
1
2
1
2
3
4
3
4
Data transmission and reception will be one-to-
one by entering same IP address to
"RECEIVING IP ADDRESS" on the setting page
of the encoder and to "DESTINATION IP
ADDRESS" on the setting page of the decoder.
one by entering same IP address to
"RECEIVING IP ADDRESS" on the setting page
of the encoder and to "DESTINATION IP
ADDRESS" on the setting page of the decoder.
• Settings for the MPEG2 Encoder
IP ADDRESS: 192.168.0.20
SOURCE PORT No.: 51000 (Same for all)
SOURCE PORT No.: 51000 (Same for all)
Camera Input CH
DESTINATION IP ADDRESS
DESTINATION PORT No.
1
1 192.168.0.30
60000
2
2 192.168.0.30
60001
3
3 192.168.0.30
60002
4
4 192.168.0.30
60003
• Settings for the MPEG2 Decoder
IP ADDRESS: 192.168.0.30
RECEIVING IP ADDRESS: 192.168.0.30 (Same for all)
RECEIVING IP ADDRESS: 192.168.0.30 (Same for all)
Monitor
Output CH
RECEIVING PORT No.
1 1
60000
2 2
60001
3 3
60002
4 4
60003
Note: When the decoder is restarted while receiving streaming video by the unicast transmission, it may take more than 10
minutes for the decoder to display streaming video.
To restart the decoder while receiving streaming video by the unicast transmission, it is recommended to do the following:
1. Click the [STOP] button on the CONTROL/STATE page of the encoder or use the
minutes for the decoder to display streaming video.
To restart the decoder while receiving streaming video by the unicast transmission, it is recommended to do the following:
1. Click the [STOP] button on the CONTROL/STATE page of the encoder or use the
"stop encoding" CGI command to stop
encoding.
2. Restart the decoder.
3. After the decoder becomes operable (after the STATUS 5 indicator of the decoder lights up), click the [START]
button on the CONTROL/STATE page of the encoder, or use the "start encoding" CGI command.
CONNECTIONS
CONNECTIONS