Netgear WGL102-100NAS 전단

)NSTALLATION

This guide describes installation for the WAGL102 ProSafe™ 802.11a/g Dual Band Light 
Wireless Access Point or WGL102 Prosafe 802.11g Light Wireless Access Point. 

Note: The WAGL102 or WGL102 Light Wireless Access Points work only in conjunction 
with the WFS709TP ProSafe Smart Wireless Switch. In order to complete access point 
installation, the WFS709TP should be already configured and available on your network. 
For instructions on advanced configuration options for access points, please refer to the 
WFS709TP ProSafe Smart Wireless Switch Software Administration Manual, which can 
be downloaded from http://www.netgear.com/support.

1.

Unpack the box and verify the contents, as follows:

•

WAGL102 ProSafe 802.11a/g Dual Band Light Wireless Access Point or 
WGL102 Prosafe 802.11g Light Wireless Access Point

•

Antenna: 

-

WAGL102—one 2.4 GHz antenna and one 5 GHz antenna

-

WGL102—one 2.4 GHz antenna

•

Wall mounting screws

•

Straight through Category 5 Ethernet cable

•

Power adapter and cord (12 V dc, 1.2 A)

•

ProSafe Light Wireless Access Point, WAGL102 or WGL102 Installation Guide 
(this document)

•

Support Registration card

Note: Contact your reseller or customer support in your area if there are any missing or 

damaged parts. You can refer to the Support Information Card for the telephone 
number of customer support in your area. You should keep the Support Information 
card, along with the original packing materials, and use the packing materials to 
repack the WAGL102 or WGL102 if you need to return it for repair.

2.

Connect the access points directly to the WFS709TP ProSafe Smart Wireless Switch 
to configure them and to download firmware (for full instructions, see the 
documentation for the WFS709TP ProSafe Smart Wireless Switch).

3.

Mount or place the access point where you intend to deploy it. 

4.

Power the access point by one of these methods:

•

Power adapter—connect to a power source using the supplied power adapter.

•

PoE (power over Ethernet)—connect an Ethernet cable between the access 
point’s 65 FE Port and:
-

A network port on a WFS709TP ProSafe Smart Wireless Switch, or

-

A network mid-span device that supports a 802.3af compliant port.

5.

Orient the antenna (for best performance, a vertical position is recommended).

6.

Verify successful installation by observing the LED status:

7.

Complete your installation by defining the operational behavior for each access point 
in your network. 

Here are some tips for correcting simple problems you may have.

•

Make sure the power is connected to the access point.

ENET (10/100 Mbps)

Green

Off

No link

Green on

10/100Mbps link negotiated

Green flashing

10/100Mbps data activity

WLAN LEDs

Green

Off

Wireless radio disabled

Green on

Wireless radio AP mode enabled

Green flashing

Wireless radio AM mode enabled

•

Make sure the Ethernet cable connectors (if used) are securely plugged in at the 
access point and the network device (hub, switch, or router). 

•

Make sure the connected device is turned on. 

•

Disconnect the adapter from its power source and then plug it in again. Contact 
NETGEAR if the Wireless LAN lights remain off.

•

Check that the WAGL102 or WGL102 is properly installed, the LAN connections are 
OK, and that the LAN port LED is green. Check the operational status of the 
WFS709TP ProSafe Smart Wireless Switch.

Maximum Clients

Limited by the amount of wireless network traffic generated by each node; 
typically 15 to 20 nodes.

Status LEDs

Power/Ethernet LAN/Wireless LAN/Test

Power Adapter

12V DC, 1 A

Environmental 
Specifications

Operating temperature: 0 to 50° C
Operating humidity: 5-95%, non-condensing

Antenna

• WAGL102: One (1) external 5dBi 2.4 GHz detachable antenna and one (1) 

external 5 dBi 5GHz detachable antenna

• WGL102: One (1) external 5 dBi 2.4 GHz detachable antenna 

Wireless LAN 
network 
standards

IEEE 802.11a, IEEE 802.11b and IEEE 802.11g

Radio technology

• 802.11b: 1 and 2 Mbps, Direct Sequence Spread Spectrum (DSSS)
• 802.11b: 5.5 and 11 Mbps, Complementary Code Keying (CCK)
• 802.11g: All rates, Orthogonal Frequency Division Multiplexing (OFDM)

Radio modulation 
type

• 802.11a - BPSK, QPSK,16-QAM, 64-QAM
• 802.11b - CCK, BPSK, QPSK
• 802.11g - CCK, BPSK, QPSK,16-QAM, 64-QAM

Media Access 
Control

CSMA/CA with ACK