Omnitron Systems Technology GX/F 전단

This DIP-Switch controls the Link Propagate or Link
Segment modes.  When the DIP-Switch is in the “LS”
position (factory setting), Link Segment mode is enabled.
In the “LP” position, Link Propagate mode is enabled.

To enable Remote Fault Detection mode, set the “RFD”
DIP-Switch to the “RFD” position.

To enable RFD + LS mode, also set the LS/LP DIP-
Switch to the “LS” position.  To enable RFD + LP mode,
set the LS/LP DIP-Switch to the “LP” position.

The RFD DIP-Switch selection is ignored on ports set to
Auto-Negotiation mode.

To enable Symmetrical Fault Detection mode, set the
“SFD” DIP-Switch to the “SFD” position, the “LS/LP”
DIP-Switch to the “LS” position and the “RFD”
DIP-Switch to the “Off” position.

Any other DIP-Switch configuration will disable
Symmetrical Fault Detection mode.

 

1
2
3
4
5
6
7
8

When the “BPAEN” DIP-Switch is in the “ON” (right) position,
the A Ethernet backplane port is enabled.  This port allows
connectivity to an adjacent module. When the “BPAEN”
DIP-Switch is in the “Off” position (left, factory setting), the
A port is isolated from the backplane.

When the Backplane B Enable “BPBEN” DIP-Switch is in the
“ON” (right) position, the B Ethernet backplane port is enabled.
This port allows connectivity to an adjacent module.  When
the “BPBEN” DIP-Switch is in the “Off” position (left, factory
setting), the B port is isolated from the backplane.

When set to the Auto-Negotiate “AN” (factory setting),
this DIP-Switch enables the Gigabit Fiber Port to sense
its duplex mode automatically.  If the connected device
cannot provide the proper signal to indicate its own
mode of operation, the P1 Manual “MAN” DIP-Switch
position should be selected to force Full-Duplex mode

on Port 1. This facilitates the connection to devices that
do not auto-negotiate properly on their Gigabit fiber port.

When the P1 1000FX Fiber is set to Auto-Negotiation
Mode, the device receiving the fault acts as if it is in
RFD mode.

The P2 Full/Half-Duplex DIP-Switch selects the duplex
mode for the 100Mbps (FX) P2 port.  When set to
Full-Duplex “FD” (left, factory setting), the P2 port
operates in Full-Duplex mode.  When set to Half-Duplex
“HD” position (right), P2 operates in Half-Duplex mode.

The following DIP-Switches are present on the GX/F
but are unused and do not affect any functionality:
4) P2 AN/MAN

6) P2 100/10

7) P2 1000/10-100

8) P2 AX/MANX

Page 15

Page 10

Page 11

Page 12

Page 9

Page 14

Page 16

Page 13

The operating description in this Instruction Manual is for use by qualified
personnel only. To avoid electrical shock, do not perform any servicing of this
unit other than that contained in the operating instructions, unless you are
qualified and certified to do so by Omnitron Systems Technology, Inc.

This product is warranted to the original purchaser against defects
in material and workmanship for a period of TWO YEARS from the
date of shipment. A LIFETIME warranty may be obtained by the
original purchaser by REGISTERING this product with Omnitron
within 90 days from the date of shipment. TO REGISTER,
COMPLETE AND MAIL OR FAX THE ENCLOSED
REGISTRATION FORM. You may also register your product on the
Internet at www.omnitron-systems.com. During the warranty period,
Omnitron will, at its option, repair or replace a product which is
proven to be defective.

For warranty service, the product must be sent to an Omnitron designated
facility, at Buyer’s expense. Omnitron will pay the shipping charge to
return the product to Buyer’s designated US address using Omnitron’s
standard shipping method.

The foregoing warranty shall not apply to defects resulting from
improper or inadequate use and/or maintenance of the equipment by
Buyer, Buyer-supplied equipment, Buyer-supplied interfacing,
unauthorized modifications or tampering with equipment (including
removal of equipment cover by personnel not specifically authorized
and certified by Omnitron), or misuse, or operating outside the
environmental specification of the product (including but not limited to
voltage, ambient temperature, radiation, unusual dust, etc.), or improper
site preparation or maintenance.

No other warranty is expressed or implied. Omnitron specifically
disclaims the implied warranties of merchantability and fitness for
any particular purpose.

The remedies provided herein are the Buyer’s sole and exclusive
remedies. Omnitron shall not be liable for any direct, indirect,
special, incidental, or consequential damages, whether based on
contract, tort, or any legal theory.

For help with this product, contact our Technical Support:

Phone:

(949) 250-6510

Fax:

(949) 250-6514

Address:

Omnitron Systems Technology, Inc.

140 Technology Dr., #500

Irvine, CA 92618 USA

E-mail:

support@omnitron-systems.com

URL:

www.omnitron-systems.com

Form:  040-08560-001C   9/07

The 

 GX/F modules are hot-swappable and

can be installed into any 

 chassis. To install

in a chassis, perform the following steps:

1. Slide the 

 module into the selected slot

while aligning it with the installation guides. Ensure
that  the  module is firmly seated against the
backplane.

2. Secure the module to the chassis using the panel

fastener screw (attached to the module).

3. Connect an appropriate multimode or single-mode

fiber cable to the Gigabit P1 fiber port.

4. Connect the cable to a compatible Gigabit device.

5. Connect an appropriate multimode or single-mode

fiber cable to the 100BASE-FX P2 fiber port.

6. Connect  the cable to a compatible 100BASE-FX

device.

Yellow

On--Power

Green

On--Full-Duplex detected

Green

On--Link / Blink--activity

Green

On--Link / Blink--activity

Green

On--Full-Duplex detected

1000BASE-SX/LX,

100BASE-FX

SC, MT-RJ, LC, 

Single-Fiber SC

BP Enable, LS/LP, RFD,

F/O Auto/Man, 
F/O FDX/HDX

Power, F/O link, FDX/HDX

W:0.85" x D:4.5" x H:2.8"

8 oz.

UL, CE, FCC Class A

1.5A @ 3.3VDC (typical)

     Standard:    0 to 50º C
          Wide:    -40 to 60º C
      Storage:    -40 to 80º C

5 to 95% (non-condensing)

-100m to 4000m

730,000