GarrettCom P62F 사용자 설명서
Magnum P62-Series Hardened Switches Installation and User Guide (12/02)
3
www GarrettCom com
.
.
Power Supply (Internal
)
24VDC and -48VDC Power Supply
Power Input Voltage: 20 to 70 VDC (auto-ranging), “-, GND, +”
Power Consumption: 10 watts typical.
DC-DC Converter Rating: 5VDC, 2Amps
Power Consumption: 10 watts typical.
DC-DC Converter Rating: 5VDC, 2Amps
Power Supply (Ext.
)
125VDC & 250VDC, (PSX-T) for P62-Series -5V only
Power Input Voltage: 100 to 275 VDC (nominal rating of 125, 250VDC)
Power Consumption: 15 watts typical.
DC-DC Converter Rating: 5VDC, 3Amps
Power Consumption: 15 watts typical.
DC-DC Converter Rating: 5VDC, 3Amps
Power Supply (External
)
AC Power Supply (PSX-A) for P62F-5V and mP62-5V
AC Power Connector: IEC-type, male recessed at rear of Power Supply chassis
Input Voltage: 85 to 264 VAC (auto-ranging)
Input Frequency: 47 to 63 Hz (auto-ranging)
Power Consumption: 15 watts typical
Power Supply Rating: 3Amps at 5VDC
Input Voltage: 85 to 264 VAC (auto-ranging)
Input Frequency: 47 to 63 Hz (auto-ranging)
Power Consumption: 15 watts typical
Power Supply Rating: 3Amps at 5VDC
Network Cable Connectors -6 RJ-45 shielded female ports and 2 fiber port
100Mbps: Category 5 UTP/STP, fiber (50/125, 62.5/125 mm, or single-mode at
9/125 micron)
10 Mbps: Category 3, 4, 5 UTP (Note: auto-sensing does not sense cable type)
Full-duplex / Half -duplex on copper (RJ-45) switched Ports # 2 to 7
All the RJ-45 ports support Full / Half duplex and 10/100 speed, each inde-
pendently auto-negotiating on P62F models; S/W controlled on mP62 models.
Fiber Ports # 1 and 8
The switched fiber ports # 1 & 8 are fixed at full-duplex only, 100Mb speed.
Mechanical
Enclosure: Rugged 18-gauge high-strength steel case. Metal mounting plate
included. Suitable for stand-alone, shelf, pedestal or wall mounting. The case also
serves as a heat sink. The metal mounting base is included, 13-guage steel.
(Without the base, the box size is only 7” high). Mounting holes in the base plate
are a rectangle that measures 3.35” x 7.92” (8.5 x 20.1 cm) center to center.
See Section 3.1.2 for additional mounting details.
Dimensions (wall mounted): 1.70 in D x 5.75 in W x 8.8 in H
serves as a heat sink. The metal mounting base is included, 13-guage steel.
(Without the base, the box size is only 7” high). Mounting holes in the base plate
are a rectangle that measures 3.35” x 7.92” (8.5 x 20.1 cm) center to center.
See Section 3.1.2 for additional mounting details.
Dimensions (wall mounted): 1.70 in D x 5.75 in W x 8.8 in H
(4.3 cm x 14.6 cm x 22.4 cm)
Weight: 3.5 lb. (1.6 kg.)
Cooling method: Convection, with case operating as a heat sink.
Note: Internal thermal materials and techniques (patent pending) conduct heat from
the electronic elements inside to the steel case which acts as a heat sink. Internal
chip temperatures are only about 10
Cooling method: Convection, with case operating as a heat sink.
Note: Internal thermal materials and techniques (patent pending) conduct heat from
the electronic elements inside to the steel case which acts as a heat sink. Internal
chip temperatures are only about 10
°
C above case ambient at steady state operation
LED Indicators
PWR:
Steady ON when power applied
SPEED: (when LINK is ON): ON = 100Mbps; OFF = 10 Mbps
LINK/ACT: Steady ON for LINK with no traffic, blinking indicates port
is transmitting / receiving.
F/H (RJ-45 ports only): ON = full-duplex, OFF = half-duplex