Delta Electronics ASDA-B 사용자 설명서
English-1
Preface
This quick start will be helpful in the installation, wiring, inspection, and operation of Delta ASDA-B series AC
servo drive and ECMA series servo motor. Before using the product, please read this quick start to ensure
correct use. You should thoroughly understand all safety precautions before proceeding with the installation,
wiring and operation. If you do not understand please contact your local Delta sales representative. Place this
quick start in a safe location for future reference. Please observe the following precautions:
servo drive and ECMA series servo motor. Before using the product, please read this quick start to ensure
correct use. You should thoroughly understand all safety precautions before proceeding with the installation,
wiring and operation. If you do not understand please contact your local Delta sales representative. Place this
quick start in a safe location for future reference. Please observe the following precautions:
Do not use the product in a potentially explosive environment.
Install the product in a clean and dry location free from corrosive and inflammable gases or liquids.
Do not connect a commercial power supply to the U, V, W terminals of motor. Failure to observe this
precaution will damage either the Servo motor or drive.
Ensure that the motor and drive are correctly connected to a ground. The grounding method must
comply with the electrical standard of the country (Please refer to NFPA 70: National Electrical Code,
2005 Ed.).
2005 Ed.).
Do not disconnect the AC servo drive and motor while the power is ON.
Do not attach, modify or remove wiring when power is applied to the AC servo drive and motor.
Before starting the operation with a mechanical system connected, make sure the emergency stop
equipment can be energized and work at any time.
Do not touch the drive heat sink or the servo motor during operation. Otherwise, it may result in
serious personnel injury.
Further information on the AC servo drive and motor can be obtained from the user manual. You can download
the user manual via the link http://www.delta.com.tw/industrialautomation/ above in PDF format.
the user manual via the link http://www.delta.com.tw/industrialautomation/ above in PDF format.
The content of this quick start may be revised without prior notice. Please consult our distributors or download
the most updated version at http://www.delta.com.tw/industrialautomation/ .
the most updated version at http://www.delta.com.tw/industrialautomation/ .
Safety Precautions
Carefully note and observe the following safety precautions when receiving, inspecting, installing, operating,
maintaining and troubleshooting. The following words, DANGER, WARNING and STOP are used to mark
safety precautions when using the Delta’s servo product. Failure to observe these precautions may void the
warranty!
maintaining and troubleshooting. The following words, DANGER, WARNING and STOP are used to mark
safety precautions when using the Delta’s servo product. Failure to observe these precautions may void the
warranty!
ASDA-B series drives are open type servo drives and must be installed in an NEMA enclosure such as a
protection control panel during operation to comply with the requirements of the international safety standards.
They are provided with precise feedback control and high-speed calculation function incorporating DSP (Digital
Signal Processor) technology, and intended to drive three-phase permanent magnet synchronous motors
(PMSM) to achieve precise positioning by means of accurate current output generated by IGBT (Insulated Gate
Bipolar Transistor).
protection control panel during operation to comply with the requirements of the international safety standards.
They are provided with precise feedback control and high-speed calculation function incorporating DSP (Digital
Signal Processor) technology, and intended to drive three-phase permanent magnet synchronous motors
(PMSM) to achieve precise positioning by means of accurate current output generated by IGBT (Insulated Gate
Bipolar Transistor).
ASDA-B series drives can be used in industrial applications and for installation in an end-use enclosure that do
not exceed the specifications defined in the ASDA-B series user manual (Drives, cables and motors are for use
in a suitable enclosure with a minimum of a UL50 type 1 or NEMA 250 Type 1 rating).
not exceed the specifications defined in the ASDA-B series user manual (Drives, cables and motors are for use
in a suitable enclosure with a minimum of a UL50 type 1 or NEMA 250 Type 1 rating).
Unpacking Check
¾
Please ensure that both the servo drive and motor are correctly matched for size (power rating).
Failure to observe this precaution may cause fire, seriously damage the drive / motor or cause
personal injury.
Failure to observe this precaution may cause fire, seriously damage the drive / motor or cause
personal injury.
Installation
¾
Do not install the product in a location that is outside the stated specification for the drive and motor.
Failure to observe this caution may result in electric shock, fire, or personal injury.
Failure to observe this caution may result in electric shock, fire, or personal injury.