Fujitsu P2X0-0202-01EN 사용자 설명서
All Rights Reserved, Copyright © FUJITSU LIMITED 2007
22
2.4 Modifying the ETERNUSmgr Top Menu System
ETERNUSmgr User Guide -Introduction- P2X0-0202-01EN
■
Output Log File
The output log file setting has the following modes:
• No log output (LOGFILE_MODE=0)
No logs are output.
In the case where a machine frequently has errors and the source of these errors is clear, a large
number of similar system log events, none of which require any follow-up, can be generated. In
such a case use the "no log" mode to allow the system to run without having to generate the useless
log files.
In the case where a machine frequently has errors and the source of these errors is clear, a large
number of similar system log events, none of which require any follow-up, can be generated. In
such a case use the "no log" mode to allow the system to run without having to generate the useless
log files.
• Output startup and error information (LOGFILE_MODE=1)
This outputs logs only when ETERNUSmgr starts up and in the event of an error. Use this mode
when space in the log area is restricted.
when space in the log area is restricted.
• Output all log information (LOGFILE_MODE=2)
This mode outputs all possible log information from the startup of ETERNUSmgr. Regardless of
its eventual success or failure, at least one log is generated by each polling event. It is recom-
mended that the system normally be run in this mode.
its eventual success or failure, at least one log is generated by each polling event. It is recom-
mended that the system normally be run in this mode.
The output mode is set by modifying the "LOGFILE_MODE" parameter in the setup file ("STX~.INI").
[Default value]
2
[Parameter]
LOGFILE_MODE(0-2)
Caution:
For this parameter, if there is no need for any special setting, it is recommended not to enter any
value. This parameter is commented out in the default setup file available after installation.
value. This parameter is commented out in the default setup file available after installation.
2.4
Modifying the ETERNUSmgr Top Menu System
The ETERNUSmgr Top Menu files are generated automatically when ETERNUSmgr is installed. See the
"ETERNUS8000, ETERNUS4000, ETERNUS2000, ETERNUS6000, ETERNUS3000 ETERNUSmgr
Install Guide" of each OS for details of installing ETERNUSmgr.
The ETERNUSmgr Top Menu is written as a typical HTML file, and can easily be edited using a text edi-
tor.
Perform the following procedures if the Web server URL and alias set during the installation or the Top
Menu Settings directory need to be changed.
There is no need to copy the files when using the directory specified during the installation as the Top
Menu Settings directory. However, in such case, be sure to make a backup copy of the top menu file
("menu.htm") before editing the original.
"ETERNUS8000, ETERNUS4000, ETERNUS2000, ETERNUS6000, ETERNUS3000 ETERNUSmgr
Install Guide" of each OS for details of installing ETERNUSmgr.
The ETERNUSmgr Top Menu is written as a typical HTML file, and can easily be edited using a text edi-
tor.
Perform the following procedures if the Web server URL and alias set during the installation or the Top
Menu Settings directory need to be changed.
There is no need to copy the files when using the directory specified during the installation as the Top
Menu Settings directory. However, in such case, be sure to make a backup copy of the top menu file
("menu.htm") before editing the original.
Caution:
• ETERNUSmgr reads the Top Menu File ("menu.htm") in, and reoutputs it after adding
the target device status information to it. Therefore, always stop ETERNUSmgr before
making any changes to the base "menu.htm" file.
making any changes to the base "menu.htm" file.
• The "menu.htm" file must be set to be writable.