Netgear XAVB5004-100NAS 전단

This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste 

Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union, 

this product should be treated and recycled in accordance with the laws of your jurisdiction 

implementing the WEEE Directive.

NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarkes and/or registered trademarks of 

NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to 

change without notice. Other brand and product names are trademarks or registered trademarks of their 

respective holders. ©2012 NETGEAR, Inc. All rights reserved. 

Do not press the Security button on the Powerline adapter until 

installation is complete and the adapters are communicating with each other 
(indicated by the blinking Powerline LED). Pressing this button too soon can 
temporarily disable Powerline communication. If this should occur, use the Factory 
Reset button to return the Powerline adapter to its factory default settings.

Ethernet

•  Solid. The Ethernet port is linked.
•  Off. There is no Ethernet connection.

Powerline

•  Solid. The adapter is connected to a Powerline network.
• Off. The adapter has not found any other compatible Powerline devices 

using the same encryption key.

The Pick A Plug feature lets you pick the electrical outlet with the strongest 
link rate, indicated by the color displayed by the LED:
Green: Link rate > 80 Mbps (Best)
Amber: Link rate > 50 and < 80 Mbps (Better)
Red: Link rate < 50 Mbps (Good)

Power

•  Solid blue: The electrical power is on.
•  Blinking blue: The adapter is in the process of resetting or security 

setup.   (Note: there is no color for power saving mode.)

•  Solid Amber: The device is in power saving mode.
•  Off. There is no electrical power.

Factory Reset  Press the Factory Reset button for 1 second, then release to return the 

Powerline adapter to its factory default settings.

Security 
Button

After you plug in your new AV adapter, press the Security button for 2 
seconds, then press the Security button on one of the other AV adapters in 
your existing network for 2 seconds. Both buttons must be pressed within 2 
minutes. 
Note: The Security button does not work in power saving mode. See 
“Power LED is amber” in the 

 table.

When connecting devices to your Ethernet ports, be aware of the Quality of Service 
(QoS) priorities assigned for each port:

Port 1 (dark green) has HIGH priority, and gives uninterrupted service to the 

connected device. Devices you would connect to Port 1 include media servers, 

storage devices, gaming consoles, video players, or internet telephones.

Port 2 (light green) has MEDIUM priority. You can connect devices such as 

gaming consoles, video players, or internet telephones to this port.

Ports 3 and 4 (yellow) have LOW priority, and are best for networking data 

devices, such as printers.

Power LED is off.

Make sure that power is supplied to the electrical outlet, and that 
the Powerline devices are not plugged into an extension cord, 
power strip, or surge protector.

Power LED is amber

Power saving mode occurs when the Ethernet LED is off. This can 
occur when:
• the Ethernet cable is unplugged. 
• the device connected through the Ethernet cable is turned off. 
• the adapter is idle for 10 minutes. 
It returns to normal mode within 2 seconds once the Ethernet link 
is up.

Powerline LED is off.

• Make sure that the Powerline devices are plugged into outlets 

with power. 

• Move the Powerline device to a closer location.
• If you have set network security, make sure that all Powerline 

devices are using the same encryption key.

• Reset the devices to factory default settings. 

Powerline LED is red.

The color of the Powerline LED indicates the speed of the 
Powerline link. If the LED is red, the speed is less than 50 Mbps. 
Switch to another electrical outlet until the LED displays solid 
green.

Ethernet LED is off.

•  Make  sure  that  the  Ethernet  cables  are  working  and securely 

plugged into the devices.

• Reset the devices to factory default settings. 

Thank you for selecting NETGEAR products. 
After installing your device, locate the serial number on the label of your product and 
use it to register your product at 

. Registration is 

required before you can use the telephone support service. Registration via our 
website is strongly recommended.
Go to 

for product updates and Web support

For additional information about setting up, configuring, and using your Powerline 
AV Adapter Kit, see the User Manual

You can also download the standard 

Powerline AV Utility, and other documentation from the NETGEAR web site at 

For complete DoC, visit the NETGEAR EU Declarations of Conformity website at: 

Do not plug any Powerline device into a powerstrip.