Epson EMP-715/505 사용자 설명서
104 - When the Indicators Provide No Help
EMP-715/505E trouble.fm
The image is cut up (Large)/Small
· The image is
disturbed.
· Noise appears
●
Has the cable been connected correctly?
see page 25, 32
see page 25, 32
●
Is the selected resolution correct?
Align the computer with the signals supported by the projector. Refer
to the computer’s instruction manual for details on how to amend the
signals.
see page 26
Align the computer with the signals supported by the projector. Refer
to the computer’s instruction manual for details on how to amend the
signals.
see page 26
●
Have the [Synchronization *, Tracking *, Display Position] settings
been correctly adjusted.
Press the [Auto] button to make the adjustments.
The [Menu] will be displayed to enable adjustment to be made.
see page 47, 65
been correctly adjusted.
Press the [Auto] button to make the adjustments.
The [Menu] will be displayed to enable adjustment to be made.
see page 47, 65
●
Has the cable length been extended?
There are cases where noise will occur if the cable length is extended.
Either use the cable supplied or connect amplification equipment, etc,
and confirm the situation.
There are cases where noise will occur if the cable length is extended.
Either use the cable supplied or connect amplification equipment, etc,
and confirm the situation.
●
Has the signal format setting for the image been set correctly?
Select the video signal format with [Menu]
Select the video signal format with [Menu]
− [Image] − [Video Signal
Format]. There are cases where the video image signals being input
cannot be determined in the [Auto] mode.
see page 67
cannot be determined in the [Auto] mode.
see page 67
●
Do the input signals match the connected equipment?
Set the signal type with the [Menu] - [Image] - [Input Signal]
parameter. Set [RGB] for computer signals, and [YCbCr] or [YPbPr]
(depending on the equipment signals) for component video signals.
see page 65
Set the signal type with the [Menu] - [Image] - [Input Signal]
parameter. Set [RGB] for computer signals, and [YCbCr] or [YPbPr]
(depending on the equipment signals) for component video signals.
see page 65
· The image is cut
up
· The image is small
●
There is a possibility that the [Resize] setting has not been correctly
selected.
Press the [Resize] button.
see page 52
selected.
Press the [Resize] button.
see page 52
●
Has the [Display Position] been correctly adjusted?
Adjust with [Menu]
Adjust with [Menu]
− [Image] − [Position].
see page 65
●
Is the selected resolution correct?
Align the computer with the signals supported by the projector. Refer
to the computer’s instruction manual for details on how to amend the
signals.
see page 26
Align the computer with the signals supported by the projector. Refer
to the computer’s instruction manual for details on how to amend the
signals.
see page 26
●
Amend the resolution for note-type and liquid crystal type
computers.
Either amend the resolution so that the display fills the entire screen,
or set the image signals so that only external output is possible.
see page 25
computers.
Either amend the resolution so that the display fills the entire screen,
or set the image signals so that only external output is possible.
see page 25
●
Has the system been set for dual display?
Only half of the computer screen’s image will be displayed with the
projector if dual display has been set with [Display Properties] on the
control panel. Cancel the dual display setting to display the entire
computer screen image. Refer to the video driver manual supplied
with the computer in use for further details.
Only half of the computer screen’s image will be displayed with the
projector if dual display has been set with [Display Properties] on the
control panel. Cancel the dual display setting to display the entire
computer screen image. Refer to the video driver manual supplied
with the computer in use for further details.
715_505E.bk Page 104 Friday, May 25, 2001 10:24 AM