JVC DLA-G150HTE 사용자 설명서

DLA-G150HTE

1-34

No.51847

If something abnormal has occurred with the projector, the warning status will be indicated by the combination of lighting the 
indicators on the control panel as shown in the following table. Then, the projector automatically stops projection and runs the 
cooling fan for about 120 seconds.

■

After the cooling fan has stopped, take the following action.

No. 1

: Chek that the cover for replacing the light-source lamp and the front panel are securely attached, and then, press 

the OPERATE button for one second or more to turn on the projector for retrying.

No. 2

: Chek that the cover for replacing the light-source lamp and the front panel are securely attached, and then, press 

the OPERATE button for one second or more to turn on the projector for retrying.

No. 3

: Press the OPERATE button for one second or more to turn on the projector for retrying.

Nos. 4-7 : Follow the next steps.

1. Turn off the MAIN POWER switch and unplug the power cord from the wall outlet.
2. Take an action according to the number.

No. 4

: Set the filter in place.Then, leave the projector until it cools down.

No. 5

: Check that nothing is blocking the air inlet nor outlet, and wait until the inside cools down.

No. 6

: Check that nothing is blocking the air inlet nor outlet, and wait until the inside cools down.

No. 7

: Leave the projector until it cools down.

3. Plug in the power cord again, turn on the MAIN POWER switch, and press the OPERATE button for one second or 

more to turn on the projector for retrying.

Plug in the power cord again and operate the projector.
If the same warning indication is observed again, after the cooling fan has stopped, turn off the MAIN POWER switch, unplug 
the power cord, and call your dealer for repair.

1

Blink

Blink

The light-source lamp does not light and projection 
is not made.

2

Blink

Blink

The light-source lamp has suddenly gone off during 
projecting an image.

3

Blink

Blink

Circuit operation is abnormal.

4

Blink

Blink

The filter is displaced.

5

Blink

The internal temperature is too high. (Sensor 1)

6

Blink

Blink

The internal temperature is too high. (Sensor 2)

7

Blink

Blink

Blink

Blink

The cooling fan has stopped (locked).

■ When warning indication is shown by the blinking indicators:

The warning status will be notified by the combination lighting of the projector’s indicators.
For the warning contents and the action to be taken, refer to  “Warning Indication” on page 64.

■

• Stains on the cabinet

These should be wiped off with a soft cloth. If the cabinet is heavily stained, wipe it with a cloth soaked in water-diluted 
neutral detergent and wring well, then wipe clean with a dry cloth.

• Since the cabinet may deteriorate in quality, become damaged, or show paint peeled, note the following:

– Do not wipe with rough cloth.
– Do not wipe vigorously.
– Do not wipe with thinner or benzene.
– Do not apply any volatile substance such as insecticides.
– Do not allow any rubber or vinyl article to remain in contact with the cabinet for a long time.

• Stains on the lens

These should be cleaned off with commercially available lens blowers or lens cleaning paper (for cleaning glasses and 
cameras).
Do not use liquid cleaning agents. This could cause the surface coating to be removed.
Do not rub, scratch or hit the lens as its surface is prone to damage.

• Is picture quality (color density, etc.) 

adjusted correctly?

• Adjust picture quality on the menu.

48

• Is the correct color system selected?

• Set the color system to AUTO or to the 

correct dedicated color system.

44

• Are signals (scanning frequency, etc.) 

of the connected devices appropriate?

• Check if the signal is appropriate (scanning 

frequency, etc.), and input the appropriate 
signal.

22

• Is the PC2 input terminal being used?  • When the PC2 input terminal is being use, 

“PC 2(BNC)” must be selected from the 
menu options. Set it correctly with the input 
signal.

11, 53

• While computer system signal is input, 

isn’t a sync signal for composite sync 
(Cs) or G on sync being input?

• Input separate sync signals for vertical sync 

(V) and horizontal sync (H) signals.

11, 28

• Isn’t signal with much jitter or skew 

distortion being input from a video 
deck?

• Input signals with little jitter or distortion.

Use a TBC or a device with a built-in TBC.

–

• Is video picture turned off by pressing 

the HIDE button?

• Turn on video picture by pressing the HIDE 

button.

10, 12, 

34

• Are batteries installed correctly?

• Match the polarities of batteries correctly (+ 

to + and – to –).

14

• Are batteries exhausted?

• Replace with new batteries.

14

• Is there a shielding object between the 

remote control unit and the remote 
sensor?

• Remove any shielding objects.

20

• Is the distance too long?

• Use the remote control unit at a nearer 

point.

20

• Is either side of remote cable 

disconnected?

• Firmly insert the remote cable when using 

the remote control unit as the wired one.

21