Neumann.Berlin KMR 82 i 사용자 설명서
4
5
KMR 82 i
Studio outlets so powered will therefore also ac-
cept dynamic microphones and ribbon micro-
phones as well as the modulation conductors of
tube-equipped condenser microphones without the
need to switch off the dc supply voltage.
cept dynamic microphones and ribbon micro-
phones as well as the modulation conductors of
tube-equipped condenser microphones without the
need to switch off the dc supply voltage.
No harm is done even if a Neumann phantom pow-
er supply is connected to the inputs of micro-
phones which are phantom powered from another
source.
er supply is connected to the inputs of micro-
phones which are phantom powered from another
source.
2.2 ac Supply Operation
All P48 power supplies in accordance with
IEC 61938 which provide at least 1 mA per
channel, are suitable for powering the micro-
phones.
IEC 61938 which provide at least 1 mA per
channel, are suitable for powering the micro-
phones.
The Neumann P48 power supply unit bears the
designation N 248. It is designed to power two
mono condenser microphones or one stereo micro-
phone at 48 V ± 1 V, max. 2 x 6 mA (see also Neu-
mann bulletin no. 68832: “Phantom 48 VDC Pow-
er Supplies”).
designation N 248. It is designed to power two
mono condenser microphones or one stereo micro-
phone at 48 V ± 1 V, max. 2 x 6 mA (see also Neu-
mann bulletin no. 68832: “Phantom 48 VDC Pow-
er Supplies”).
The assignment of the microphone terminals and
the modulation polarity at the power supply out-
put are identical to those at the microphone.
the modulation polarity at the power supply out-
put are identical to those at the microphone.
The N 248 supplies one stereo microphone, or two
mono condenser microphones with 48 V phantom
power (P48). All connectors are of XLR 3 type. The
audio signal outputs are DC-free.
mono condenser microphones with 48 V phantom
power (P48). All connectors are of XLR 3 type. The
audio signal outputs are DC-free.
Three versions are available:
N 248 EU ............ blk ............. Cat. No. 08537
N 248 US ............ blk ............. Cat. No. 08538
N 248 UK ............ blk ............. Cat. No. 08539
N 248 US ............ blk ............. Cat. No. 08538
N 248 UK ............ blk ............. Cat. No. 08539
2.3 Battery Powering
If a mains power source is not available, power
can be supplied by one of the battery units
can be supplied by one of the battery units
BS 48 i .................................... Cat. No. 06494
(for one microphone)
(for one microphone)
BS 48 i-2 ................................. Cat. No. 06496
(for two microphones)
(for two microphones)
Both units deliver 48 V ± 1 V, at 5 mA maximum,
and are powered by a 9-volt monobloc battery
Type IEC 6 F 22.
and are powered by a 9-volt monobloc battery
Type IEC 6 F 22.
The BS 48 i-2 is equipped with 5-pin XLR connec-
tors, the BS 48 i with 3-pin XLR connectors.
tors, the BS 48 i with 3-pin XLR connectors.
(See Neumann bulletin 68832... “Phantom 48 VDC
Power Supplies”.)
Power Supplies”.)
The modulation is connected to pins 2 and 3; the
shield is connected to pin 1. A sudden increase in
sound pressure in front of the microphone dia-
phragm causes a positive voltage to appear at pin 2.
shield is connected to pin 1. A sudden increase in
sound pressure in front of the microphone dia-
phragm causes a positive voltage to appear at pin 2.
The 3-pin XLR connector has the following pin as-
signments:
signments:
Pin 1: 0 V/ground
Pin 2: Modulation (+phase),
Pin 2: Modulation (+phase),
Pin 3: Modulation (–phase).
1.2 Microphone Cables
The following cables are available for the KMR 81 i
microphone:
microphone:
IC 3 mt ................ blk ............. Cat. No. 06543
Microphone cable with double twist (double he-
lix) braiding as shield. Ø 5 mm, length 10 m.
XLR 3 connectors, matte black.
lix) braiding as shield. Ø 5 mm, length 10 m.
XLR 3 connectors, matte black.
IC 31 mt (5 m) .... blk ............. Cat. No. 06570
Microphone cable with double twist (double helix)
braiding as shield. Textile-braided to avoid friction-
al noise due to the handling of booms or plastic
leadings (for example in windscreens). Ø 4,5 mm,
length 5 m. XLR 3 connectors, matte black.
braiding as shield. Textile-braided to avoid friction-
al noise due to the handling of booms or plastic
leadings (for example in windscreens). Ø 4,5 mm,
length 5 m. XLR 3 connectors, matte black.
AC 25 (0.3 m) ......................... Cat. No. 06600
Adapter cable with XLR 3 M connector and unbal-
anced 6.3 mm mono jack. It is used to connect 3-
pin XLR outputs of power supplies to units with a
6.3 mm monojack input. Designed for all micro-
phones, excluding KM 100 System and GFM 132.
anced 6.3 mm mono jack. It is used to connect 3-
pin XLR outputs of power supplies to units with a
6.3 mm monojack input. Designed for all micro-
phones, excluding KM 100 System and GFM 132.
Special cable lengths can be made to order.
2.
Power Supply
2.1 Phantom Powering
The KMR 82 i is phantom powered at 48 V (P48,
IEC 61938).
IEC 61938).
With phantom powering the dc from the positive
supply terminal is divided via two identical resis-
tors, one half of the dc flowing through each au-
dio (modulation) conductor to the microphone, and
returning to the voltage source via the cable
shield. Phantom powering provides a fully com-
patible connecting system, since no potential dif-
ferences exist between the two audio conductors.
supply terminal is divided via two identical resis-
tors, one half of the dc flowing through each au-
dio (modulation) conductor to the microphone, and
returning to the voltage source via the cable
shield. Phantom powering provides a fully com-
patible connecting system, since no potential dif-
ferences exist between the two audio conductors.
Die Modulationsadern liegen an Pin 2 und 3, die
Abschirmung an Pin 1. Bei einem Schalldruckan-
stieg vor der Mikrophonmembran tritt an Pin 2 eine
positive Spannung auf.
Abschirmung an Pin 1. Bei einem Schalldruckan-
stieg vor der Mikrophonmembran tritt an Pin 2 eine
positive Spannung auf.
Der 3-polige XLR-Steckverbinder hat folgende
Belegung:
Belegung:
Pin 1: 0 V/Masse
Pin 2: Modulation (+Phase)
Pin 2: Modulation (+Phase)
Pin 3: Modulation (–Phase).
1.2 Mikrophonkabel
Für das KMR 81 i stehen folgende Kabel zur Verfü-
gung:
gung:
IC 3 mt ............... sw ............ Best.-Nr. 06543
Mikrophonkabel mit Doppeldrallumspinnung als
Abschirmung. Ø 5 mm, Länge 10 m. XLR 3 Steck-
verbinder, schwarzmatt.
Abschirmung. Ø 5 mm, Länge 10 m. XLR 3 Steck-
verbinder, schwarzmatt.
IC 31 mt (5 m) ... sw ............ Best.-Nr. 06570
Mikrophonkabel mit Doppeldrallumspinnung als
Abschirmung. Textilumsponnen, zur Vermeidung
von Reibgeräuschen bei der Verwendung an Mi-
krophonangel oder Windschutzkorb. Ø 4,5 mm,
Länge 5 m. XLR 3 Steckverbinder, schwarzmatt.
Abschirmung. Textilumsponnen, zur Vermeidung
von Reibgeräuschen bei der Verwendung an Mi-
krophonangel oder Windschutzkorb. Ø 4,5 mm,
Länge 5 m. XLR 3 Steckverbinder, schwarzmatt.
AC 25 (0,3 m) ...................... Best.-Nr. 06600
Adapterkabel mit XLR 3 F-Buchse und 6,3 mm Mo-
noklinkenstecker, unsymmetrisch, für den An-
schluss des 3-poligen XLR-Ausganges eines Spei-
segerätes an Geräte mit 6,3 mm Monoklinken-
buchse. Für alle Mikrophone mit Ausnahme der
Ausgangsstufe KM 100 und des GFM 132.
noklinkenstecker, unsymmetrisch, für den An-
schluss des 3-poligen XLR-Ausganges eines Spei-
segerätes an Geräte mit 6,3 mm Monoklinken-
buchse. Für alle Mikrophone mit Ausnahme der
Ausgangsstufe KM 100 und des GFM 132.
Andere Kabellängen sind auf Wunsch lieferbar.
2.
Stromversorgung
2.1 Phantomspeisung
Das KMR 82 i wird mit 48 V phantomgespeist (P48,
IEC 61938).
IEC 61938).
Bei der Phantomspeisung fließt der Speisestrom
vom positiven Pol der Spannungsquelle über die
elektrische Mitte der beiden Modulationsadern
zum Mikrophon. Er wird hierzu über zwei gleich-
große Widerstände beiden Tonadern gleichsinnig
zugeführt. Die Rückleitung des Gleichstroms er-
folgt über den Kabelschirm. Zwischen beiden Mo-
dulationsadern besteht also keine Potentialdiffe-
renz. Daher ist mit der Phantomspeisung eine kom-
patible Anschlusstechnik möglich:
vom positiven Pol der Spannungsquelle über die
elektrische Mitte der beiden Modulationsadern
zum Mikrophon. Er wird hierzu über zwei gleich-
große Widerstände beiden Tonadern gleichsinnig
zugeführt. Die Rückleitung des Gleichstroms er-
folgt über den Kabelschirm. Zwischen beiden Mo-
dulationsadern besteht also keine Potentialdiffe-
renz. Daher ist mit der Phantomspeisung eine kom-
patible Anschlusstechnik möglich:
Auf die Anschlussdosen können wahlweise auch
dynamische Mikrophone oder Bändchenmikropho-
ne sowie die Modulationskabel röhrenbestückter
Kondensatormikrophone geschaltet werden, ohne
dass die Speisegleichspannung abgeschaltet wer-
den muss.
dynamische Mikrophone oder Bändchenmikropho-
ne sowie die Modulationskabel röhrenbestückter
Kondensatormikrophone geschaltet werden, ohne
dass die Speisegleichspannung abgeschaltet wer-
den muss.
Der Ausgang eines Neumann-Phantomspeisegerä-
tes darf auch auf bereits anderweitig phantomge-
speiste Mikrophoneingänge gesteckt werden.
tes darf auch auf bereits anderweitig phantomge-
speiste Mikrophoneingänge gesteckt werden.
2.2 Betrieb mit Netzgeräten
Für die Stromversorgung sind alle P48-Netzgerä-
te geeignet, die mindestens 1 mA je Kanal abge-
ben.
te geeignet, die mindestens 1 mA je Kanal abge-
ben.
Das Neumann P48-Netzgerät hat die Bezeichnung
N 248. Es ist zur Stromversorgung zweier Mono-
Kondensatormikrophone oder eines Stereomikro-
phons mit 48 V ± 1 V, maximal 2 x 6 mA, geeignet
(siehe auch Neumann-Druckschrift 68832: „48 V-
Phantomspeisegeräte“).
N 248. Es ist zur Stromversorgung zweier Mono-
Kondensatormikrophone oder eines Stereomikro-
phons mit 48 V ± 1 V, maximal 2 x 6 mA, geeignet
(siehe auch Neumann-Druckschrift 68832: „48 V-
Phantomspeisegeräte“).
Die Zuordnung der Mikrophonanschlüsse und die
Polarität der Modulationsadern ist am Ausgang
des Speisegerätes die gleiche wie am Mikrophon.
Polarität der Modulationsadern ist am Ausgang
des Speisegerätes die gleiche wie am Mikrophon.
Das Netzgerät N 248 versorgt ein oder zwei Mikro-
phone mit 48 V-Phantomspeisung P48. Alle An-
schlüsse mit XLR 3-Flanschdosen. Die Modulati-
onsausgänge sind gleichspannungsfrei.
phone mit 48 V-Phantomspeisung P48. Alle An-
schlüsse mit XLR 3-Flanschdosen. Die Modulati-
onsausgänge sind gleichspannungsfrei.
Das Gerät ist in drei Ausführungen erhältlich:
N 248 EU ............ sw ............ Best.-Nr. 08537
N 248 US ............ sw ............ Best.-Nr. 08538
N 248 UK ............ sw ............ Best.-Nr. 08539
N 248 US ............ sw ............ Best.-Nr. 08538
N 248 UK ............ sw ............ Best.-Nr. 08539
2.3 Batteriespeisung
Steht keine Netzspannung zur Verfügung, kann die
Speisung mit einem der Geräte
Speisung mit einem der Geräte
BS 48 i .................................. Best.-Nr. 06494
(für ein Mikrophon)
(für ein Mikrophon)
BS 48 i-2 ............................... Best.-Nr. 06496
(für zwei Mikrophone)
(für zwei Mikrophone)
erfolgen. Beide Geräte liefern 48 V ± 1 V, maximal
je 5 mA, und werden jeweils von einer 9 Volt-
Blockbatterie Typ IEC 6 F 22 gespeist.
je 5 mA, und werden jeweils von einer 9 Volt-
Blockbatterie Typ IEC 6 F 22 gespeist.
Das Gerät BS 48 i-2 ist mit 5-poligen, das BS 48 i
mit 3-poligen XLR-Steckverbindern ausgerüstet.
mit 3-poligen XLR-Steckverbindern ausgerüstet.
(Siehe auch Neumann-Druckschrift 68832... „48 V-
Phantomspeisegeräte“).
Phantomspeisegeräte“).