Grizzly G0555X 사용자 설명서
G0555X
(Mfg. Since 1/12)
-13-
Main components: (figure 3)
Qty
A. stand .......................................................... 1
B. bandsaw unit ............................................. 1
c. trunnion base ............................................ 1
D. lever board ................................................ 1
E. Miter gauge ................................................ 1
f. extension table .......................................... 1
G. Main table .................................................. 1
h. Fence assembly ......................................... 1
I. resaw Fence ............................................. 1
J. Front Fence rail ......................................... 1
K. rear Fence rail ......................................... 1
fasteners and Tools: (not shown)
Qty
•
rubber Feet (stand) .................................. 4
•
hex nuts
3
⁄
8
-16 (Feet/stand) ...................... 8
•
Flat Washers 10mm (Feet/stand) .............. 8
•
hex bolts M8-1.25 x 35 (bandsaw/stand) . 4
•
Flat Washers 8mm (bandsaw/stand) ........ 8
•
lock Washers 8mm (bandsaw/stand) ....... 4
•
hex nuts M8-1.25 (bandsaw/stand) .......... 4
•
hex bolts M8-1.25 x 30 (trunnion base) ... 2
•
lock Washers 8mm (trunnion base)......... 2
•
hex bolt M8-1.25 x 80 (positive stop) ....... 1
•
hex nut M8-1.25 (positive stop) ............... 1
•
spacers (lever board) ............................... 4
•
Cap screws M8-1.25 x 60 (lever board) .. 4
•
hex nuts M8-1.25 (lever board) ............... 4
•
set screws M8-1.25 x 20 (lever board) .... 4
•
Cap screws M6-1 x 25 (lever board) ....... 4
•
lock Washers 6mm (lever board) ............ 4
•
Flat Washers 6mm (lever board) .............. 4
•
Knobs M10-1.5 (table) .............................. 2
•
hex bolts M6-1 x 20 (Front rail) ............... 2
•
Flat Washers 6mm (Front rail) .................. 2
•
lock Washers 6mm (Front rail) ................ 2
•
Cap screws M6-1 x 16 (rear rails) .......... 2
•
lock handle M8-1.25 x 20 (Fence) ............ 1
•
hex nut M8-1.25 (Fence) ........................... 1
Inventory
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
a
b
C
d
e
F
g
h
i
J
K
figure 3. Main components inventory.
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
•
Moving plate (resaw) ................................ 1
•
lock handle M8-1.25 x 44 (resaw) ........... 1
•
Flat Washer 8mm (resaw) ........................ 1
•
hex Wrenches 3, 4, 5mm .................1 each