Bosch DGSH181BL 사용자 설명서
-5-
Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. The operator can
control torque reactions or kickback forces, if
proper precautions are taken.
position your body and arm to allow you to
resist kickback forces. The operator can
control torque reactions or kickback forces, if
proper precautions are taken.
Use special care when working corners,
sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag the
rotating accessory and cause loss of control or
kickback.
sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag the
rotating accessory and cause loss of control or
kickback.
Do not attach a toothed saw blade. Such
blades create frequent kickback and loss of
control.
blades create frequent kickback and loss of
control.
Always feed the bit into the material in the
same direction as the cutting edge is exiting
from the material (which is the same
direction as the chips are thrown). Feeding
the tool in the wrong direction causes the
cutting edge of the bit to climb out of the work
and pull the tool in the direction of this feed.
same direction as the cutting edge is exiting
from the material (which is the same
direction as the chips are thrown). Feeding
the tool in the wrong direction causes the
cutting edge of the bit to climb out of the work
and pull the tool in the direction of this feed.
Safety warnings specific for
grinding and abrasive
cutting-off operations:
Use only wheel types that are
recommended for your power tool and only
for recommended applications. For
example: do not grind with the side of a
cut-off wheel. Abrasive cut-off wheels are
intended for peripheral grinding, side forces
applied to these wheels may cause them to
shatter.
recommended for your power tool and only
for recommended applications. For
example: do not grind with the side of a
cut-off wheel. Abrasive cut-off wheels are
intended for peripheral grinding, side forces
applied to these wheels may cause them to
shatter.
For threaded abrasive cones and plugs use
only undamaged wheel mandrels with an
unrelieved shoulder flange that are of
correct size and length. Proper mandrels will
reduce the possibility of breakage.
only undamaged wheel mandrels with an
unrelieved shoulder flange that are of
correct size and length. Proper mandrels will
reduce the possibility of breakage.
Do not “jam” a cut-off wheel or apply
excessive pressure. Do not attempt to
make an excessive depth of cut.
Overstressing the wheel increases the loading
and susceptibility to twisting or snagging of the
wheel in the cut and the possibility of kickback
or wheel breakage.
excessive pressure. Do not attempt to
make an excessive depth of cut.
Overstressing the wheel increases the loading
and susceptibility to twisting or snagging of the
wheel in the cut and the possibility of kickback
or wheel breakage.
Do not position your hand in line with and
behind the rotating wheel. When the wheel,
at the point of operation, is moving away from
your hand, the possible kickback may propel
the spinning wheel and the power tool directly
at you.
behind the rotating wheel. When the wheel,
at the point of operation, is moving away from
your hand, the possible kickback may propel
the spinning wheel and the power tool directly
at you.
When wheel is pinched, snagged or when
interrupting a cut for any reason, switch off
the power tool and hold the power tool
motionless until the wheel comes to a
complete stop. Never attempt to remove
the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may
occur. Investigate and take corrective action to
eliminate the cause of wheel pinching or
snagging.
interrupting a cut for any reason, switch off
the power tool and hold the power tool
motionless until the wheel comes to a
complete stop. Never attempt to remove
the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may
occur. Investigate and take corrective action to
eliminate the cause of wheel pinching or
snagging.
Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed
and carefully re-enter the cut. The wheel
may bind, walk up or kickback if the power tool
is restarted in the workpiece.
workpiece. Let the wheel reach full speed
and carefully re-enter the cut. The wheel
may bind, walk up or kickback if the power tool
is restarted in the workpiece.
Support panels or any oversized workpiece
to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag under
their own weight. Supports must be placed
under the workpiece near the line of cut and
near the edge of the workpiece on both sides
of the wheel.
to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag under
their own weight. Supports must be placed
under the workpiece near the line of cut and
near the edge of the workpiece on both sides
of the wheel.
Use extra caution when making a “pocket
cut” into existing walls or other blind areas.
The protruding wheel may cut gas or water
pipes, electrical wiring or objects that can
cause kickback.
cut” into existing walls or other blind areas.
The protruding wheel may cut gas or water
pipes, electrical wiring or objects that can
cause kickback.
BM 2610034444 04-14_DGSH181 4/2/14 11:24 AM Page 5