Bosch 1811PSD 사용자 설명서

-3-

Power Tool-Specific Safety Warnings

Safety Warnings Common for Grinding,

Sanding, Wire Brushing, and Abrasive

Cutting-Off Operations:

a) This power tool is intended to function

as a grinder, sander, wire brush or cut-
off tool. Read all safety warnings,
instructions,

illustrations

and

specifications  provided  with  this  power
tool.  Failure  to  follow  all  instructions  listed
below  may  result  in  electric  shock,  fire
and/or serious injury.

b) This power tool is not recommended for

polishing. Operations for which the power
tool was not designed may create a hazard
and cause personal injury.

c) Do not use accessories which are not

specifically designed and recommended
by  the  tool  manufacturer.  Just  because
the  accessory  can  be  attached  to  your
power  tool,  it  does  not  assure  safe
operation.

d) The rated speed of the accessory must

be at least equal to the maximum speed
marked on the power tool. Accessories
running faster than their RATED SPEED
can break and fly apart.

e) The outside diameter and the thickness

of  your  accessory  must  be  within  the
capacity  rating  of  your  power  tool.
Incorrectly  sized  accessories  cannot  be
adequately guarded or controlled.

f) The arbor size of wheels, flanges,

backing  pads  or  any  other  accessory
must  properly  fit  the  spindle  of  the
power  tool.  Accessories  with  arbor  holes
that do not match the mounting hardware of
the  power  tool  will  run  out  of  balance,
vibrate  excessively  and  may  cause  loss  of
control.

g) Do not use a damaged accessory. Before

each use inspect the accessory such as
abrasive  wheels  for  chips  and  cracks,
backing  pad  for  cracks,  tear  or  excess
wear,  wire  brush  for  loose  or  cracked
wires.  If  power  tool  or  accessory  is
dropped, inspect for damage or install an
undamaged accessory.  After inspecting
and  installing  an  accessory,  position
yourself  and  bystanders  away  from  the
plane  of  the  rotating  accessory  and  run
the  power  tool  at  maximum  no-load
speed  for  one  minute.  Damaged
accessories will normally break apart during
this test time.

b) Do not use the power tool if the switch

does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.

c) Disconnect the plug from the power

source  and/or  the  battery  pack  from  the
power  tool  before  making  any
adjustments,  changing  accessories,  or
storing  power  tools.  Such  preventive
safety  measures  reduce  the  risk  of  starting
the power tool accidentally.

d) Store idle power tools out of the reach of

children  and  do  not  allow  persons
unfamiliar  with  the  power  tool  or  these
instructions  to  operate  the  power  tool.
Power  tools  are  dangerous  in  the  hands  of
untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,
breakage of parts and any other
condition that may affect the power

tool’s  operation.  If  damaged,  have  the
power  tool  repaired  before  use.  Many
accidents  are  caused  by  poorly  maintained
power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.

g) Use the power tool, accessories and tool

bits  etc.  in  accordance  with  these
instructions,  taking  into  account  the
working  conditions  and  the  work  to  be
performed.  Use  of  the  power  tool  for
operations  different  from  those  intended
could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a

qualified  repair  person  using  only
identical  replacement  parts.  This  will
ensure  that  the  safety  of  the  power  tool  is
maintained.

BM 1609929J65 01-11:BM 1609929J65 01-11 1/20/11 10:41 AM Page 3