Market Forge Industries ST-6E 사용자 설명서
3
INSTALLATION
Remove the four screws in the right side hinge
mounting holes and install them in the left side hinge
mounting holes (where the hinges were originally
mounted).
Using the nuts removed in step #6, reinstall the door
Using the nuts removed in step #6, reinstall the door
interlock assembly onto the two screws in the lower
left hinge mounting holes (see Fig. 1) with by mov-
ing the assembly over the cooking cavity to the other
side of the unit. Rotate the door interlock assembly
180° for installation, so that the switch is now facing
up.
Reinstall the top hinge and screws into the right low-
Reinstall the top hinge and screws into the right low-
er hinge mounting holes. Rotate the hinge 180° for
installation, so that the pin which the door rides on is
now facing up. The hinge must be rotated because
it will now function as the bottom hinge. DO NOT
COMPLETELY TIGHTEN THE HINGE for installation
so that the pin which the door rides on now facing up.
The hinge must be rotated because it will now func-
tion as the bottom hinge. DO NOT COMPLETELY
TIGHTEN THE HINGE MOUNTING SCREWS YET.
These will be used later for adjusting the door.
Remove the door latch assembly from the face of the
Remove the door latch assembly from the face of the
unit. The two nuts mounting the door latch are locat-
ed behind the face of the unit and must be accessed
where the right side panel was removed.
Remove the two white hole plugs from the left door
Remove the two white hole plugs from the left door
8.
9.
10.
11.
12.
INTERLOCK
ASSEMBLY
ORIGINAL
POSITION
INTERLOCK
ASSEMBLY
POSITION WHEN
DOOR IS REVERSED
DOOR LATCH
ASSEMBLY
(ORIGINAL POSITION)
TOP RIGHT HINGE
MOUNTING
HOLES
LOWER LEFT
HINGE
MOUNTING
HOLES
LOWER RIGHT
HINGE
MOUNTING
HOLES
TOP LEFT
HINGE
MOUNTING
HOLES
LEFT DOOR
LATCH
MOUNTING
HOLES
D
2"
51mm
3"
76mm
24"
610mm
30"
762mm
1.5"
38mm
.5"
13mm
5 Pan
23.2"
589mm
3 Pan
16.7"
424mm
2"
51mm
1"
25mm
4"
102mm
3"
76mm
15.8"
400mm
20.4"
518mm
D
CW
E
Electrical Connection
Cold Water
Drain Connection
E -
CW -
D -
Fig. 1 Dimensions
Fig. 2 Typical Door Layout
latch mounting holes, and insert them into the right
door latch mounting holes (where the door latch as-
sembly was originally mounted).
Rotate the door latch assembly 180°, and install into
Rotate the door latch assembly 180°, and install into
the left door latch mounting holes. (NOTE: Each stud
on the latch assembly should have a plastic washer,
a spring, a plastic washer and a Nyloc type nut.)
To adjust the tension of the door latch, tighten both
To adjust the tension of the door latch, tighten both
nuts down until the springs are fully compressed,
then back each nut off 1 1/2 turn.
Rotate the door 180° for mounting.
Slide the remaining hinge into the top door bearing.
Slide the door and hinge assembly down onto the
Rotate the door 180° for mounting.
Slide the remaining hinge into the top door bearing.
Slide the door and hinge assembly down onto the
hinge which you have already mounted to the front of
the unit. Use the two screws to mount the top hinge
into the right upper hinge mounting holes. DO NOT
COMPLETELY TIGHTEN THE HINGE MOUNTING
SCREWS YET.
Slowly push the cooking compartment door closed
Slowly push the cooking compartment door closed
until it is latched.
The cooking compartment door can now be raised,
The cooking compartment door can now be raised,
lowered, and/or rotated into position by bumping it
with the palm of your hand or by using a small rub-
ber mallet.
First, check the alignment at the front of the door by
First, check the alignment at the front of the door by
making sure that the striker in the door is centered
with the latch mechanism on the front of the unit.
13.
14.
15.
16.
17.
16.
17.
18.
19.
20.