Cecilware ICAP1 사용자 설명서
5
IV. POUROVER-PORTABLE BOTTLE OPERATION (Toggle UP, Water Selection Switch, on the back panel)
UNIT CAN BE OPERATED WITH A 3 GALLONS CAPACITY FRESH WATER BOTTLE.
TO OPERATE WITH PORTABLE BOTTLE, proceed AS FOLLOWS:
1. Remove Reservoir Tank Cover.
2. Make sure that Reservoir Tank is only 1/2 full or empty, to prevent water splillage.
To remove excess water push dispense button.
3. Fill bottle with water .
4. Invert bottle into reservoir tank in one motion to minimize spillage.
5. Remove and refill bottle when “REFILL“ light is ON.
NOTE: REFILL LIGHT, ON THE FRONT DOOR PANEL, WILL GO ON, WHICH INDICATES THAT THE WATER TANK MUST
BE REFILLED. WHEN REFILL LIGHT GOES ON, THE UNIT WILL NOT DISPENSE UNTIL TANK IS FILLED WITH WATER.
REFILLING WITH HOT TAP WATER WILL SHORTEN HEAT UP TIME.
V. NORMAL OPERATION
(POUROVER AND AUTOREFILL)
1. Place a 6 oz. or larger cup under dispense nozzle,
UNIT CAN BE OPERATED WITH A 3 GALLONS CAPACITY FRESH WATER BOTTLE.
TO OPERATE WITH PORTABLE BOTTLE, proceed AS FOLLOWS:
1. Remove Reservoir Tank Cover.
2. Make sure that Reservoir Tank is only 1/2 full or empty, to prevent water splillage.
To remove excess water push dispense button.
3. Fill bottle with water .
4. Invert bottle into reservoir tank in one motion to minimize spillage.
5. Remove and refill bottle when “REFILL“ light is ON.
NOTE: REFILL LIGHT, ON THE FRONT DOOR PANEL, WILL GO ON, WHICH INDICATES THAT THE WATER TANK MUST
BE REFILLED. WHEN REFILL LIGHT GOES ON, THE UNIT WILL NOT DISPENSE UNTIL TANK IS FILLED WITH WATER.
REFILLING WITH HOT TAP WATER WILL SHORTEN HEAT UP TIME.
V. NORMAL OPERATION
(POUROVER AND AUTOREFILL)
1. Place a 6 oz. or larger cup under dispense nozzle,
then press and hold dispense switch (green) for 6
seconds.
seconds.
The machine will dispense water at the rate of 1 oz.
per second. Repeat it several times to check for con-
sistent output.
sistent output.
2. While the tank is heating up, remove the hopper,
load with product and reposition it back in the ma-
chine.
chine.
When Heater Light goes OFF, the tank has reached
its brew temperature and the machine is ready to
begin dispensing the first cup of Cappuccino.
begin dispensing the first cup of Cappuccino.
VI. WATER FLOW and
DRINK STRENGTH ADJUSTMENTS
THE UNIT IS FACTORY ADJUSTED TO DISPENSE
WATER AND POWDER AT THE RATE OF 1.0 oz/
sec.
sec.
TO INCREASE OR DECREASE FLOW, PROCEED AS
FOLLOWS:
1. Remove left side panel and locate Dispense Valve
Flow Adjuster on top of Heated Tank.
2. Locate Flow Adjustment Screw (white) on Dispense
Valve.
3. Rotate Adjustment Screw Counterclockwise to IN-
CREASE flow rate.
4. Rotate Clockwise to DECREASE flow rate.
When making strength adjustments, do not adjust
by more than 1/4 turn at a time, without checking
drink strength (ratio of water to powder).
When making strength adjustments, do not adjust
by more than 1/4 turn at a time, without checking
drink strength (ratio of water to powder).
WATER FLOW
ADJUSTMENT,
SCREW ON
DISPENSE
VALVE
RESERVOIR
TANK
RESERVOIR
COVER
INDICATOR
LIGHT- RED
"REFILL TANK
WHEN ON"
DISPENSE
BUTTON
BOTTLE
HOT WATER TANK
DRIP TRAY
Illustration No. 3 – ICAP 1 B LD POUROVER