Vermont Casting IRHEDV32 사용자 설명서
12
10003929
1.
STOP! Read the safety information above on this label.
2.
Turn off all electrical power to the fireplace.
3.
For MN/MP/TN/TP appliances ONLY, go on to Step 4.
For RN/RP appliances turn the On/Off switch to off
position or set thermostat to lowest level.
For RN/RP appliances turn the On/Off switch to off
position or set thermostat to lowest level.
4.
Open control access panel.
5.
Push in gas control knob slightly and turn clockwise
to "OFF". Do not force.
to "OFF". Do not force.
6.
Wait five (5) minutes to clear out any gas. Then smell
for gas, including near the floor. If you smell gas,
STOP! Follow "B" in the safety information above on
this label. If you don't smell gas, go to the next step.
for gas, including near the floor. If you smell gas,
STOP! Follow "B" in the safety information above on
this label. If you don't smell gas, go to the next step.
7.
Remove window frame assembly before lighting pilot.
(See Window Frame Assembly Removal in manual).
(See Window Frame Assembly Removal in manual).
8.
Visibly locate pilot by the main burner.
9.
Turn knob on gas control counterclockwise
to "PILOT".
to "PILOT".
TO TURN OFF GAS TO FIREPLACE
4.
Push in gas control knob slightly and
turn clockwise
turn clockwise
to "OFF". Do
not force.
5.
Close control access panel.
10. Push the control knob all the way in and hold.
Immediately light the pilot by repeatedly de-
pressing the piezo spark ignitor until a flame
appears. Continue to hold the control knob in for
about one (1) minute after the pilot is lit. Re-
lease knob and it will pop back up. Pilot should
remain lit. If it goes out, repeat steps 5 through 8.
pressing the piezo spark ignitor until a flame
appears. Continue to hold the control knob in for
about one (1) minute after the pilot is lit. Re-
lease knob and it will pop back up. Pilot should
remain lit. If it goes out, repeat steps 5 through 8.
• If knob does not pop up when released, stop
and immediately call your service technician or
gas supplier.
gas supplier.
• If after several tries, the pilot will not stay lit,
turn the gas control knob to "OFF" and call
your service technician or gas supplier.
your service technician or gas supplier.
11. Replace window frame assembly.
12. Turn gas control knob to "On" position.
13. For Rn/RP appliances turn the On/Off switch to
12. Turn gas control knob to "On" position.
13. For Rn/RP appliances turn the On/Off switch to
"On" positin or set thermostat to desired setting.
14. Turn on all electrical power to the fireplace.
•
If you cannot reach your gas supplier, call the
Fire Department
Fire Department
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will
not push in or turn by hand, do not try to repair
it, call a qualified service technician. Applying
force or any attempted repair may result in a
fire or explosion.
not push in or turn by hand, do not try to repair
it, call a qualified service technician. Applying
force or any attempted repair may result in a
fire or explosion.
D. Do not use this fireplace if any part has been
under water. Immediately call a qualified
service technician to inspect the fireplace and
to replace any part of the control system and
any gas control which has been under water.
service technician to inspect the fireplace and
to replace any part of the control system and
any gas control which has been under water.
FOR YOUR SAFETY READ BEFORE LIGHTING
A. This fireplace has a pilot which must be lit manually.
When lighting the pilot follow these instructions
exactly.
exactly.
B. BEFORE LIGHTING smell all around the fireplace
area for gas. Be sure to smell next to the floor be-
cause some gas is heavier than air and will settle on
the floor.
cause some gas is heavier than air and will settle on
the floor.
WHAT TO DO IF YOU SMELL GAS
•
•
Do not try to light any fireplace.
•
Do not touch any electric switch
•
Do not use any phone in your building
•
Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
phone. Follow the gas supplier's instructions.
TO TURN OFF GAS TO FIREPLACE
LIGHTING AND OPERATING INSTRUCTIONS
1.
Turn the On/Off switch to Off position or set
the thermostat to lowest setting.
the thermostat to lowest setting.
2.
Turn off all electric power to the fireplace if
service is to be performed.
service is to be performed.
3.
Open control access panel.
EURO SIT
SIT NOVA
HONEYWELL
WARNING:
If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
may result causing property damage, personal injury or loss of life.
PILOT
ON
OFF
ON
PILOT
O
F
F
OFF
HI
OFF
PILOT
LO
3/8" - 1/2"
LIGHTING INSTRUCTIONS