Maytag MFT2771WEM 사용자 설명서
10
Water and Ice Dispenser
(on some models)
Depending on your model, you may have one or more of the
following options: the ability to select crushed or cubed ice; a
rotating water dispenser faucet and pull-out tray; a special light
that turns on when you use the dispenser; a lock option to avoid
unintentional dispensing; or an indicator that tells you when there
has been a power outage.
following options: the ability to select crushed or cubed ice; a
rotating water dispenser faucet and pull-out tray; a special light
that turns on when you use the dispenser; a lock option to avoid
unintentional dispensing; or an indicator that tells you when there
has been a power outage.
IMPORTANT: The language of the text on the display screen can
be set to English, Spanish or French. For information about
changing the language, see “Using the Controls.”
be set to English, Spanish or French. For information about
changing the language, see “Using the Controls.”
NOTES:
■
The dispensing system will not operate when the refrigerator
door is open.
door is open.
■
After connecting the refrigerator to a water source, flush the
water system. Use a sturdy container to depress and hold the
water dispenser pad for 5 seconds, then release it for
5 seconds. Repeat until water begins to flow. Once water
begins to flow, continue depressing and releasing the
dispenser pad (5 seconds on, 5 seconds off) for an additional
5 minutes. This will flush air from the filter and water
dispensing system. Additional flushing may be required in
some households. As air is cleared from the system, water
may spurt out of the dispenser.
water system. Use a sturdy container to depress and hold the
water dispenser pad for 5 seconds, then release it for
5 seconds. Repeat until water begins to flow. Once water
begins to flow, continue depressing and releasing the
dispenser pad (5 seconds on, 5 seconds off) for an additional
5 minutes. This will flush air from the filter and water
dispensing system. Additional flushing may be required in
some households. As air is cleared from the system, water
may spurt out of the dispenser.
■
Allow 24 hours for the refrigerator to cool down and chill
water.
water.
■
Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
first three batches of ice produced.
■
The display screen on the dispenser control panel has a
backlight, which will turn off automatically when the controls
have not been used for 2 minutes or more. When the
backlight is off, the first press of a control button or the
display screen will only reactivate the backlight, without
changing any settings. Within 2 minutes after the backlight
has been reactivated, additional presses of control buttons or
the display screen will change the applicable settings.
backlight, which will turn off automatically when the controls
have not been used for 2 minutes or more. When the
backlight is off, the first press of a control button or the
display screen will only reactivate the backlight, without
changing any settings. Within 2 minutes after the backlight
has been reactivated, additional presses of control buttons or
the display screen will change the applicable settings.
The Water Dispenser
IMPORTANT: Dispense enough water every week to maintain a
fresh supply.
fresh supply.
The default display unit for water dispensing is ounces. The units
can be changed to cups or liters.
can be changed to cups or liters.
To Dispense Water (Standard):
1. Press a sturdy glass against the water dispenser pad OR
place the glass below the water dispenser and press the
water dispenser button.
water dispenser button.
2. Remove the glass OR release the button to stop dispensing.
To Dispense Water (Measured Fill):
Measured Fill allows you to dispense a specified amount of water
with the touch of a few buttons.
with the touch of a few buttons.
NOTE: The amount of water you select will be dispensed. Be
sure that the container is empty and can hold the entire volume. If
ice is in the container, you may need to adjust your selection.
sure that the container is empty and can hold the entire volume. If
ice is in the container, you may need to adjust your selection.
1. Press WATER on the display screen to turn the feature on.
NOTE: The dispenser will automatically exit the Measured Fill
screen after 15 seconds of inactivity.
screen after 15 seconds of inactivity.
2. You can dispense water by the ounce, cup, or liter. Press
UNITS to select your desired setting. Minimum and maximum
volumes are listed below.
volumes are listed below.
3. Press the up and down arrows to adjust the volume as
desired.
NOTE: Most coffee cups (commonly 4 to 6 oz [118 to
177 mL] per cup) are not the same size as a measuring cup
(8 oz [237 mL]). You may need to adjust the volume to avoid
unintentionally overfilling coffee cups.
177 mL] per cup) are not the same size as a measuring cup
(8 oz [237 mL]). You may need to adjust the volume to avoid
unintentionally overfilling coffee cups.
4. To dispense water, press a sturdy glass against the water
dispenser pad OR place the glass below the water dispenser
and press the water dispenser button.
and press the water dispenser button.
NOTE: While dispensing water, the digital display will count
down how much water remains to be dispensed, according
to the volume you selected. The flow of water will
automatically stop once the desired volume has been
dispensed.
down how much water remains to be dispensed, according
to the volume you selected. The flow of water will
automatically stop once the desired volume has been
dispensed.
5. To stop dispensing before the selected volume has been
dispensed, remove the glass from the dispenser pad OR
press the water dispenser button a second time.
press the water dispenser button a second time.
NOTE: If you stop dispensing before the desired volume has
been dispensed, the digital display will continue to show how
much water remains to be dispensed. The display will exit the
Measured Fill screen after 15 seconds of inactivity.
been dispensed, the digital display will continue to show how
much water remains to be dispensed. The display will exit the
Measured Fill screen after 15 seconds of inactivity.
To select a new volume or select the same volume again, you
must first finish dispensing the selected volume, or turn off
the Measured Fill feature and then turn it back on.
must first finish dispensing the selected volume, or turn off
the Measured Fill feature and then turn it back on.
Preset Volumes
The dispenser can store up to three preset water volumes, for
easy dispensing into commonly used containers.
easy dispensing into commonly used containers.
■
To store presets, press WATER, then PRESET. Locate a blank
or unwanted preset on the display screen. Press and hold
that preset for 3 seconds, and the preset adjustment menu
will appear on the display screen. Adjust the units and volume
of water as desired, as instructed in steps 2 and 3 of the
previous section. Press PRESET to save the preset.
or unwanted preset on the display screen. Press and hold
that preset for 3 seconds, and the preset adjustment menu
will appear on the display screen. Adjust the units and volume
of water as desired, as instructed in steps 2 and 3 of the
previous section. Press PRESET to save the preset.
■
To use presets, press WATER, then PRESET, then press and
release the desired preset. Dispense water as instructed in
steps 4 and 5 of the previous section.
release the desired preset. Dispense water as instructed in
steps 4 and 5 of the previous section.
Units
Minimum
Maximum
Ounces
1
128
Cups
¹/₄
16
Liters
0.05
4