Heartland 3530 사용자 설명서
49
Section 8: Troubl Shooting
Gas Trouble Shooting Chart
P ro b lem
C a u se
R em ed y
N o sparks w hen
any control knob
is turned to
“light”
any control knob
is turned to
“light”
N o pow er to spark m odule -
m odule sw itch faulty
m odule sw itch faulty
C heck electrical supply to spark m odule
w ith voltm eter - replace m odule
w ith voltm eter - replace m odule
N o sparks w hen
one or som e
control knob(s) is
(are) turned to
“light”
one or som e
control knob(s) is
(are) turned to
“light”
R e-ignition electrode
controlled by knob sw itch is
grounded or has a high
resistance leak
controlled by knob sw itch is
grounded or has a high
resistance leak
C heck high voltage w ires carefully for
loose connections or pinches in the
w ires; if connections are tight, replace
high voltage w ire
loose connections or pinches in the
w ires; if connections are tight, replace
high voltage w ire
Sparking occurs at
electrodes w hen
all control knobs
are turned off
electrodes w hen
all control knobs
are turned off
D isconnected sw itch lead or
short in sw itch lead
short in sw itch lead
C heck all sw itch lead connections for
looseness and w ires for dam age
looseness and w ires for dam age
A ll burners that
are turned on
have lighted but
electrodes are still
sparking
are turned on
have lighted but
electrodes are still
sparking
H igh resistance or open
connection betw een spark
output term inal and H .V. w ire
receptacle (spark w ill jum p
sm all gap but sensing current
w ill not)
connection betw een spark
output term inal and H .V. w ire
receptacle (spark w ill jum p
sm all gap but sensing current
w ill not)
Push receptacles firm ly onto all
term inals
C heck positioning of shrink sleeving on
receptacle – should be flush w ith end of
receptacle – trim if necessary
term inals
C heck positioning of shrink sleeving on
receptacle – should be flush w ith end of
receptacle – trim if necessary
D efective m odule
R eplace m odule
G round/Earth lead to m odule
disconnected or range chassis
not properly connected to
ground/earth by ground/earth
lead or through third prong of
pow er cord plug, com bined
w ith reversed pow er supply
polarity
disconnected or range chassis
not properly connected to
ground/earth by ground/earth
lead or through third prong of
pow er cord plug, com bined
w ith reversed pow er supply
polarity
C heck ground/earth connection of range
chassis and ground/earth lead
connection to m odule
chassis and ground/earth lead
connection to m odule
Flam e jetting off
outer head burner
ring or inner head
burner ring
outer head burner
ring or inner head
burner ring
Too m uch air
Pots too large
Pots too large
R educe size of air shutter opening until
flam e is no longer jetting off burner
head
flam e is no longer jetting off burner
head
N uisance sparking
w hen one or both
w hen one or both
grill burners are
on
on
Too m uch air
Pots too large
R educe size of air shutter opening until
flam e is no longer jetting off burner
flam e is no longer jetting off burner
head.(Flam e jetting off burner)
Note: Random sparking after burner lights or uneven flame from burner - please refer to
page 36 for proper burner assembly (burner rings not properly positioned on burner
base). Some ticking is normal from time to time.
base). Some ticking is normal from time to time.