Maytag CGR1415ADH 사용자 설명서
Component Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power and gas to oven before servicing,
unless testing requires power and/or gas.
unless testing requires power and/or gas.
16
16023522
©2004 Maytag Services
Illustration Component
Test
Procedure
Results
M1 Controlled
Oven temperature
adjustment
adjustment
Press
Bake
pad.
Enter
550
on the digit-pad.
Immediately press and hold
Bake
pad
for 3 to 5 seconds.
Oven can be adjusted from -35 to +35
degrees in 5-degree increments by
pressing
Oven can be adjusted from -35 to +35
degrees in 5-degree increments by
pressing
More +
or
Less -
pads. To
avoid over adjusting the oven, move
temperature 5 degrees each time.
Wait 4 seconds for the data entry
timer to expire to accept the change.
Temperature adjustment is retained
even through a power failure.
temperature 5 degrees each time.
Wait 4 seconds for the data entry
timer to expire to accept the change.
Temperature adjustment is retained
even through a power failure.
While increasing or decreasing oven
temperature, this does not affect self-
cleaning temperature.
temperature, this does not affect self-
cleaning temperature.
M1 Controlled
Temperature display
Press and hold
Cancel
and
Bake
pads for 3 to 5 seconds. Press
More +
or
Less -
pads to change.
This mode enables the user to indicate
°F or °C on the display.
°F or °C on the display.
M1 Controlled
Clock Display
Press and hold
Cancel
and
Clock
pads for 3 to 5 seconds.
Allows clock to be toggled On or OFF.
M1 Controlled
24 Hour Clock
Press and hold
Cancel
and
Delay
pads for 3 to 5 seconds. Press
More +
or
Less -
pads to change.
Allows the time on the clock to be
toggled from 12 hour or 24 hour display.
toggled from 12 hour or 24 hour display.
M1 Controlled
Factory Default
Press and hold
Cancel
and
Keep
Warm
pads for 3 to 5 seconds until
beep sounds.
Allows the clock to be reset to factory
settings.
settings.
M1 Controlled
Twelve hour off
Control will automatically cancel any
cooking operation and remove all relay
drives 12 hours after the last pad
touch.
cooking operation and remove all relay
drives 12 hours after the last pad
touch.
See Sabbath mode to disable.
M1 Controlled
Sabbath Mode
Hold
Clock
pad for 3 to 5 seconds to
activate Sabbath mode.
Hold
Hold
Clock
pad for 3 to 5 seconds to
disable Sabbath mode.
Desired bake function must be
initiated before entering Sabbath
mode.
Desired bake function must be
initiated before entering Sabbath
mode.
"SAb" will be displayed and flash for 5
seconds then remain on until until timed-
out or cancelled.
The status “SAB” is NOT fault code 5A6.
All pad inputs are disabled except for
CANCEL and CLOCK pads.
This mode disables the normal 12 hour
shutoff to allow operation of the bake
mode for a maximum of 72 hours.
The oven light is not disabled.
seconds then remain on until until timed-
out or cancelled.
The status “SAB” is NOT fault code 5A6.
All pad inputs are disabled except for
CANCEL and CLOCK pads.
This mode disables the normal 12 hour
shutoff to allow operation of the bake
mode for a maximum of 72 hours.
The oven light is not disabled.
M1 Controlled
Child lock out
Press and hold
Cancel
and
Cook &
Hold
pads for 3 to 5 seconds until
beep sounds.
To reactivate the control, press and
hold
To reactivate the control, press and
hold
Cancel
and
Cook & Hold
pads
for 3 to 5 seconds.
This is a safety feature that can be used
to prevent children from accidentally
programming the oven. It disables the
electronic oven control.
Child lockout features must be reset after
a power failure.
to prevent children from accidentally
programming the oven. It disables the
electronic oven control.
Child lockout features must be reset after
a power failure.
M1 Controlled
Diagnostic Code
Display
Display
Press and hold
More +
pad
within 60
seconds of powering up the unit.
Cycle through the codes using the
More +
or
Less -
pads.
The last 5 diagnostic codes will be stored
in the non-volatile memory.
See "Description of Error Codes" for
explanation.
in the non-volatile memory.
See "Description of Error Codes" for
explanation.