Vermont Casting DVT38IN 사용자 설명서
29
Chateau™
20011956
�����
�����������
����
�����������
����
Log
Burner
Overlay
Log Grate Burner
LG401
Figure 43
1. Position the Log Grate Burner. Remove the two
(2) screws that attach the fettle to the burner. Place
the log grate burner between the notch on the front
of the burner housing behind the burner tube. (Fig.
43) Hold the log in place and set the fettle back in
position. When the fettle is in position, it must hook
onto the log. Refasten fettle in place. NOTE: The log
should look as if it has fallen off the grate.
the log grate burner between the notch on the front
of the burner housing behind the burner tube. (Fig.
43) Hold the log in place and set the fettle back in
position. When the fettle is in position, it must hook
onto the log. Refasten fettle in place. NOTE: The log
should look as if it has fallen off the grate.
2. Position the Log Burner Overlay. The overlay is
very fragile and must be handled with extra care.
Hold the overlay with the flat surface facing down.
Hold the overlay with the flat surface facing down.
The notch for the pilot on the overlay should be in
the right rear corner. Set the overlay on top of the
burner housing toward the back. The overlay must
line up with the sides and back of the burner. The
overlay rests behind the log grate burner. Make sure
the pilot hood lines up with the notch on the overlay.
(Fig. 43)
the right rear corner. Set the overlay on top of the
burner housing toward the back. The overlay must
line up with the sides and back of the burner. The
overlay rests behind the log grate burner. Make sure
the pilot hood lines up with the notch on the overlay.
(Fig. 43)
3. Position the Andirons. Set the andirons in place by
hooking the tabs on the back of the andiron over the
outermost web of the fettle. (Figs. 49 & 50)
outermost web of the fettle. (Figs. 49 & 50)
4. Place the Volcanic Rock. Place the volcanic rocks
over the hearth refractories in front of the burner
tube and around the burner assembly as desired.
tube and around the burner assembly as desired.
(Figs. 49 & 50)
5. Place the Small Lava Rock. Place the
small lava rock approximately 1¹⁄₂” (38 mm)
wide behind the lip mounted to the burner
housing. Place ember material lightly di-
rectly behind the lava rock and the overlay.
(Figs. 49 & 50)
6. Place the Ember Material. Place the
ember material in front and around the
burner tube and behind the burner
tube in front of the burner hous-
ing. Build up the ember material
lightly over the burner tube into
the burner housing to cover up the
burner tube and the lip mounted
to the front of the burner housing.
(Figs. 49 & 50) NOTE: Placing
platinum ember material is
ing. Build up the ember material
lightly over the burner tube into
the burner housing to cover up the
burner tube and the lip mounted
to the front of the burner housing.
(Figs. 49 & 50) NOTE: Placing
platinum ember material is
mandatory for proper carry over of flame into the
burner tube.
burner tube.
Log Grate Right
Log Front Left
Log Front Middle Left
Log Front Upper Right
Log Rear Upper Middle
Log Grate Left
Log Rear Right
Log Grate Burner
Log Front Middle Right
Log Rear Left
Log Burner Overlay
Log Front Right
LG413
DVT44
Log ID
4/05
DVT44
Log ID
4/05
DVT44IN Logs
LG413
Fig. 42 DVT44IN log identification.