Husqvarna K750 사용자 설명서
14 –
English
FUEL HANDLING
Fuel
CAUTION! The machine is equipped with a two-stroke engine
and must always been run using a mixture of gasoline and
two-stroke engine oil. It is important to accurately measure
the amount of oil to be mixed to ensure that the correct
mixture is obtained. When mixing small amounts of fuel, even
small inaccuracies can drastically affect the ratio of the
mixture.
and must always been run using a mixture of gasoline and
two-stroke engine oil. It is important to accurately measure
the amount of oil to be mixed to ensure that the correct
mixture is obtained. When mixing small amounts of fuel, even
small inaccuracies can drastically affect the ratio of the
mixture.
Gasoline
•
Use good quality unleaded gasoline.
•
The lowest recommended octane grade is 87
((RON+MON)/2). If you run the engine on a lower octane
grade than 87 so-called knocking can occur. This gives
rise to a high engine temperature and increased bearing
load, which can result in serious engine damage.
((RON+MON)/2). If you run the engine on a lower octane
grade than 87 so-called knocking can occur. This gives
rise to a high engine temperature and increased bearing
load, which can result in serious engine damage.
K750
Two-stroke oil
•
For best results and performance use HUSQVARNA two-
stroke engine oil, which is specially formulated for our air-
cooled two stroke-engines.
stroke engine oil, which is specially formulated for our air-
cooled two stroke-engines.
•
Never use two-stroke oil intended for water-cooled
engines, sometimes referred to as outboard oil (rated
TCW).
engines, sometimes referred to as outboard oil (rated
TCW).
•
Never use oil intended for four-stroke engines.
Mixing ratio
1:50 (2%) for all engines.
Mixing
•
Always mix the gasoline and oil in a clean container
intended for fuel.
intended for fuel.
•
Always start by filling half the amount of the gasoline to be
used. Then add the entire amount of oil. Mix (shake) the
fuel mixture. Add the remaining amount of gasoline.
used. Then add the entire amount of oil. Mix (shake) the
fuel mixture. Add the remaining amount of gasoline.
•
Mix (shake) the fuel mixture thoroughly before filling the
machine’s fuel tank.
machine’s fuel tank.
•
Do not mix more than one month’s supply of fuel at a time.
•
If the machine is not used for some time the fuel tank
should be emptied and cleaned.
should be emptied and cleaned.
K750 OilGuard
Two-stroke oil
Use HUSQVARNA OilGuard two stroke oil.
Mixing ratio
1:50 (2 %) with HUSQVARNA OilGuard oil
Mixing
•
Always mix the gasoline and oil in a clean container
intended for fuel.
intended for fuel.
•
Always start by filling half the amount of the gasoline to be
used. Then add the entire amount of oil. Mix (shake) the
fuel mixture. Add the remaining amount of gasoline.
used. Then add the entire amount of oil. Mix (shake) the
fuel mixture. Add the remaining amount of gasoline.
•
Mix (shake) the fuel mixture thoroughly before filling the
machine’s fuel tank.
machine’s fuel tank.
•
Do not mix more than one month’s supply of fuel at a time.
•
If the machine is not used for some time the fuel tank
should be emptied and cleaned.
should be emptied and cleaned.
!
WARNING! Always ensure there is adequate
ventilation when handling fuel.
ventilation when handling fuel.
Gasoline, litre
Two-stroke oil, litre
2% (1:50)
5
0,10
10
0,20
15
0,30
20
0,40
US gallon
US fl. oz.
1
2 1/2
2 1/2
6 1/2
5
12 7/8
Gasoline, litre
Two stroke oil OilGuard, litre
2% (1:50)
5
0,10
10
0,20
15
0,30
20
0,40