Exmark LAZER Z HP 사용자 설명서
- 38 -
h)
Loosen the two (2) top chain bolts in slots in the rear deck lift arms. Loosen
jam nuts and back off the socket head adjusting screws on the bottom of the
arms until the chains are just loose. Turn the socket head adjusting screws in
until slack is taken out of each chain. Tighten the jam nuts. Tighten the chain
bolts in the deck lift arms making sure they don’t move while tightening.
jam nuts and back off the socket head adjusting screws on the bottom of the
arms until the chains are just loose. Turn the socket head adjusting screws in
until slack is taken out of each chain. Tighten the jam nuts. Tighten the chain
bolts in the deck lift arms making sure they don’t move while tightening.
i)
Loosen the four (4) nuts which secure the front swivels (two per side) until
the front chains are loose and front of deck is supported by the 3/4” (19 mm)
block. Do not loosen the front chain hardware.
the front chains are loose and front of deck is supported by the 3/4” (19 mm)
block. Do not loosen the front chain hardware.
j)
On left side, adjust front swivel using the locking nut behind the swivel until
the front chain is tight and all slack is removed from linkage. Do not lift
front of deck off 3/4” (19 mm) block. Secure front swivel using locking nut
in front of swivel. Repeat for right side.
the front chain is tight and all slack is removed from linkage. Do not lift
front of deck off 3/4” (19 mm) block. Secure front swivel using locking nut
in front of swivel. Repeat for right side.
k)
Recheck that the 3/4” (19 mm) blocks fit just snugly under the brackets and
that the tension on all the chains are approximately equal. Make sure all chain
attachment bolts are tight. Reposition anti-scalp rollers and tighten securely.
that the tension on all the chains are approximately equal. Make sure all chain
attachment bolts are tight. Reposition anti-scalp rollers and tighten securely.
FIGURE 12
SWIVEL ADJUSTMENT
SPRING COMPRESSION ADJUSTMENT
l)
Raise deck lift lever to the 5” (12.7 cm) cutting height position See Figure 10.
Adjust spring compression until proper distance is obtained between the two
large washers (See Figure 12). Adjustment is made by turning the nut at the
front of each spring (clockwise will shorten the spring, counter-clockwise will
lengthen the spring). Lock in position with jam nuts.
Adjust spring compression until proper distance is obtained between the two
large washers (See Figure 12). Adjustment is made by turning the nut at the
front of each spring (clockwise will shorten the spring, counter-clockwise will
lengthen the spring). Lock in position with jam nuts.
NOTE: When above adjustments have been made, the front of the
deck will be slightly lower than the rear of the deck.
deck will be slightly lower than the rear of the deck.
5.2.3
Pump Drive Belt Tension.
Self-tensioning - No adjustment necessary.
5.2.4
Mule Drive Belt Tension Adjustment.
Self-tensioning idler, adjust as follows:
a) Stop engine, wait for all moving parts to stop, and remove key.
b) Check to make sure the center of the bolt head in the center of the spring
loaded pulley, on left side engine deck support, is positioned between the
centers of the two alignment holes in the left support plate (See Figure 13).
It is necessary to adjust the belt tension when the center of the bolt head is at
or below the center of the bottom alignment hole.
centers of the two alignment holes in the left support plate (See Figure 13).
It is necessary to adjust the belt tension when the center of the bolt head is at
or below the center of the bottom alignment hole.
c)
When adjustment is necessary, loosen the idler pulley on the right-hand
side so it can move up and down in the slot.
side so it can move up and down in the slot.
Place a wrench on the 3/8” nut in the center of the spring loaded pulley and
apply upward pressure to relieve tension on the spring (a 1/2” drive breaker
bar and 9/16 socket works best).
apply upward pressure to relieve tension on the spring (a 1/2” drive breaker
bar and 9/16 socket works best).
Front of Unit
11 1/8” (28.3 cm) For 52” Deck
10 1/2” (26.7 cm) For 60” Deck
11 1/2” (29.2 cm) For 72” Deck
10 1/2” (26.7 cm) For 60” Deck
11 1/2” (29.2 cm) For 72” Deck