ATTO Technology diamond array vt 사용자 설명서
63
ATTO Technology Inc. Diamond Storage Array Installation and Operation Manual
9.2 Resetting Defaults
Resetting the Diamond-VT to defaults will not alter the RAID configuration, zoning configuration, IP
configuration or Telnet information. However, resetting the Diamond-VT to factory defaults is a last-ditch effort
to recover from corrupt configurations or complete failure. All data will be lost, but the zoning configuration will
remain.
configuration or Telnet information. However, resetting the Diamond-VT to factory defaults is a last-ditch effort
to recover from corrupt configurations or complete failure. All data will be lost, but the zoning configuration will
remain.
CAUTION
CAUTION
Data will be lost if you follow these
procedures. Make sure you have no other
choice before resetting the Diamond-VT to
factory defaults.
procedures. Make sure you have no other
choice before resetting the Diamond-VT to
factory defaults.
Default
If you need to return to the default settings of the
Diamond-VT but do not want to lose data or Ethernet
settings, use the CLI command
Diamond-VT but do not want to lose data or Ethernet
settings, use the CLI command
RestoreConfiguration
default
in CLI mode or in the Advanced CLI
configuration page of the ExpressNAV interface.
Note
Using
RestoreConfiguration default
or
RestoreConfiguration factory default
will not
affect the zoning configuration. To restore the
Diamond-VT to factory default, type
Diamond-VT to factory default, type
ZoneClearAll
ZoneCommit
ZoneCommit
Return to Default settings
1
Connect to Diamond-VT services via the RS-232
port or the optional Ethernet management
services card (see
port or the optional Ethernet management
services card (see
Accessing the Diamond-VT
on
page 15). You should now be in Command Line
Interface. Continue with the CLI or access the
ExpressNAV interface (see
Interface. Continue with the CLI or access the
ExpressNAV interface (see
ATTO ExpressNAV:
Browser-based Interface
on page 23).
Note
Because the ExpressNAV pages take you
through this process easily, the following
instructions are based on the CLI commands.
Use these instructions as a guide in ExpressNAV.
through this process easily, the following
instructions are based on the CLI commands.
Use these instructions as a guide in ExpressNAV.
2
Type
RestoreConfiguration default
to reset the
system configuration (See Exhibit 9.2-2 for a list of
configurations which will be changed).
configurations which will be changed).
3
Type
FirmwareRestart
or cycle power of the
Diamond-VT.
4
Reboot the host PC after the Diamond-VT
completes its power on cycle.
completes its power on cycle.
Factory Default
Resetting the Diamond-VT to factory defaults is a last-
ditch effort to recover from corrupt configurations or
complete failure. All data will be lost.
ditch effort to recover from corrupt configurations or
complete failure. All data will be lost.
Note
Using
RestoreConfiguration default
or
RestoreConfiguration factory default
will not
affect the zoning configuration. To restore the
Diamond-VT to factory default, type
Diamond-VT to factory default, type
ZoneClearAll
ZoneCommit
ZoneCommit
To reset to Factory Defaults, firmware version
2.5.3 or higher
2.5.3 or higher
1
Connect to Diamond-VT services via the RS-232
port or the optional Ethernet management
services card (see
port or the optional Ethernet management
services card (see
Accessing the Diamond-VT
on
page 15). You should now be in Command Line
Interface.
Interface.
2
Continue with the CLI or access the ExpressNAV
interface (see
interface (see
ATTO ExpressNAV: Browser-based
Interface
on page 23).
Note
Because the ExpressNAV pages take you
through this process easily, the following
instructions are based on the CLI commands.
Use these instructions as a guide in ExpressNAV.
through this process easily, the following
instructions are based on the CLI commands.
Use these instructions as a guide in ExpressNAV.
3
Type
RestoreConfiguration factorydefault
to reset
the system configuration. (See Exhibit 9.2-2 for a
list of configurations which will be changed).
list of configurations which will be changed).
4
Type
FirmwareRestart
or cycle the Diamond-VT
power.
5
Reboot the host PC after the Diamond-VT
completes its power on cycle.
completes its power on cycle.