EIKI lc-xs25 사용자 가이드

Note: This equipment  has been tested and found to comply with the limits for a Class B digital  device, pursuant to 
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in 
a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed 
and  used  in  accordance  with  the  instructions,  may  cause  harmful  interference  to  radio  communications.  However, 
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following measures:
  – Reorient or relocate the receiving  antenna.
  – Increase the separation between the equipment and receiver.
  – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  – Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do  not  make  any  changes  or  modifications  to  the  equipment  unless  otherwise  specified  in  the  instructions.  If  such 
changes or modifications should be made, you could be required to stop operation of the equipment.
Model Number 

: LC-XS25 / LC-XS30

Trade Name 

: EIKI

Responsible party  : EIKI International,Inc.
Address 

: 30251 Esperanza Rancho Santa Margarita CA 92688-2123

Telephone No. 

: 800-242-3454 (949-457-0200)

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.  

AC  Power  Cord  used  in  the  United  States  and  Canada  is  listed  by  the  Underwriters 
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the 
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable 
to insert the plug into the outlet, contact your electrician.

GROUND

This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of 
the plug.  Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, 
marked  thus 

.  If  the  fuse  cover  is  detachable,  never  use  the  plug  with  the  cover  omitted.  If  a  replacement  fuse 

cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse 
covers are available from the Parts Department indicated in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably prepared and the correct plug fitted. 
WARNING  :  A  PLUG  WITH  BARED  FLEXIBLE  CORD  IS  HAZARDOUS  IF  ENGAGED  IN  A  LIVE  SOCKET 
OUTLET .
The Wires in this mains lead are coloured in accordance with the following code:
  Green-and-yellow . . . . . . Earth
  Blue . . . . . . . . . . . . . . . . . Neutral
  Brown  . . . . . . . . . . . . . . . Live
As  the  colours  of  the  wires  in  the  mains  lead  of  this  apparatus  may  not  correspond  with  the  coloured  markings 
identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the 
letter E or by the safety earth symbol 

 or coloured green or green-and-yellow.

The  wire  which  is  coloured  blue  must  be  connected  to  the  terminal  which  is  marked  with  the  letter  N  or  coloured 
black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
WARNING: THIS APPARATUS MUST BE EARTHED .