Mitsubishi wd-57733 사용자 설명서

Note:  To operate other audio/video devices:
•  See Appendix D, “Programming the Remote 

Control.”

•  See chapter 6, “NetCommand,” for NetCommand 

IR “Learning” of device keys.

•  For HDMI devices compatible with the TV’s 

NetCommand for HDMI feature, see below.

ChannelView shows memorized channels on 

ANT 1 

and 

ANT 2.  It displays channel names and program 

information as sent by broadcasters or your local cable 
service provider and may be incomplete

.  No program 

information is displayed for analog channels.  An analog 
channel name is displayed only if you assigned a name 
in the 

Setup > Edit menu.

To receive ChannelView updates, set the Energy Mode 
to 

Fast Power On and leave the TV powered off for a 

while each day.

See ChannelView listings 
from 

ANT 1 or ANT 2.

Press 

Close ChannelView

Press 

GUIDE or EXIT.

Scan channels one by one. Press and hold   or  .
Scan channels quickly.

Press and hold 

PAGE   /  .

Jump to listings for a spe-
cific channel.

1.  Enter the channel 

number (see numbers  
in upper left.

2.  Press 

ENTER.

See more of the program 
description.

Press 

INFO.

Move navigation to the 
program guide.

Press  .

Move navigation to the 
channel guide.

Press  .

Tune to the highlighted 
channel.

Press 

ENTER.

Use any of these methods to enable the recording and 
playback commands:

•  Program the remote control for your DVR, VCR, or 

DVD player/recorder and set the slide switch to 

VCR, 

DVD, CABLE/SAT, or AUDIO as appropriate.

•  Y and 734 series TVs:  Perform NetCommand IR 

“learning” for the device.

•  Check HDMI devices for compatibility with the TV’s 

NetCommand for HDMI feature (see below).

  (PAUSE):  Pauses a VCR, DVR, or DVD.  See 

above for use during TV viewing.

  (PLAY):  Plays a VCR, DVR,  or DVD.

  (RECORD):  Records with a VCR or DVR.

  (STOP):  Stops play of a VCR, DVR, or DVD.

  (REVERSE):  Rewinds a VCR.  Reverse scans a 

DVR or DVD.

  (FORWARD):  Fast forwards a VCR.  Forward 

scans a DVR or DVD.

•  Use only alkaline batteries.
•  Be within 20 feet of the equipment.
•  Do not press two or more buttons at the same time 

unless instructed to do so.

•  Do not allow unit to get wet or become heated.
•  Avoid dropping on hard surfaces.
•  Do not use harsh chemicals to clean.  Use only a 

soft, lightly moistened cloth.

•  Do not mix old and new batteries.

If the slide switch is set to 

TV and the TV does not 

respond properly, reset the remote control.
1.  Press and hold 

POWER for several seconds until the 

button blinks twice and goes off.

2.  Release the 

POWER button.

3.  Press keys 

0   0   9   3   5 and the POWER button will blink 

twice when you finish entering the code.  While 
entering the code, pause for a moment between 
each key press to ensure it is recognized.

If you press a key and the 

POWER key blinks five times, 

replace the remote control’s batteries.

The TV’s remote may operate some functions of 
compatible HDMI devices able to receive commands 
through the HDMI cable.  Test your equipment with the 
TV’s remote to find out which commands are sup-
ported.  See below for commands that may be avail-
able, depending on the individual device.

Press 

PLAY on the device itself to:

•  Turn on the TV if not already on
•  Switch to the device (no need to display the 

Selection menu)

•  Begin play of the device

VCR, DVD, and DVR functions that may be available:

        

CH   / 

Digits 

0–9,  —

F1 (content)

CANCEL  (to cancel)