Meade lx200r 지침 매뉴얼

Attach microfocuser: Remove the dust cap from the rear cell port (5, Fig. 1) of
the telescope. Thread the microfocuser adapter (B, Fig. 6) onto the rear cell port
thread. Slide the microfocuser (C, Fig. 6) over the microfocuser adapter and tight-
en the three hex screws (K, Fig. 6) using the provided hex key.

5.

1.25" Diagonal Prism Users: If using the 1.25" diagonal prism (G, Fig. 6), slide
the 1.25" adapter (D, Fig. 6) into the microfocuser. Line up the thumbscrew into
the groove in the microfocuser (Fig. 7a and 7b). Tighten the microfocuser thumb-
screws (I, Fig. 6) to a firm feel only. Slide the 1.25" diagonal prism into the adapter
(D, Fig. 6). Tighten the accessory adapter thumbscrew (H, Fig. 6) to a firm feel
only.

SC Optional Accessory Users: If using any of the optional accessories (such as
the Off-Axis Guider, T-Adapter, etc.; see page 44) with the 

LX200R SC

models, slide

the supplied SC accessory adapter (L, Fig. 6) into the microfocuser. Line up the
groove on the side of the adapter with either of the microfocuser thumbscrews (Fig.
8a and 8b) and tighten that thumbscrew to a firm feel only. Slide the optional acces-
sory into the accessory adapter. Tighten the other microfocuser thumbscrew to a
firm feel only.

2.0" Diagonal Mirror Users: If using the 2.0" diagonal mirror, slide the mirror
directly into the microfocuser. The adapters (H and L, Fig. 6) are not required.
Tighten the thumbscrews (I, Fig. 6) to a firm feel only.

Plug in the microfocuser: Plug the microfocuser into the Focus port (13C, Fig.
1).

6.

Insert eyepiece: Remove the Series 5000 26mm 5-element Plössl eyepiece  (1,
Fig. 1) from its container and place it in the diagonal prism (G, Fig. 6) or diago-
nal mirror. Tighten the eyepiece holder thumbscrew (2, Fig. 1) to a firm feel only.
Rotate the mirror lock knob (9, Fig. 1) towards the “Unlock” position, until it feels
loose—the telescope is shipped with the mirror locked.

7.

Remove dust cover: Remove the dust cover (18, Fig. 1) from the optical tube
assembly (19, Fig. 1) by gently prying it off.

8.

Attach the handbox holder: Remove the handbox holder from the plastic bag.
If necessary, loosen the lock knob (A, Fig. 10a) and place the clamp (B, Fig. 10a)
about one of the fork arm handles (15, Fig. 1). Tighten the lock knob to a firm feel.
Slide the AutoStar II handbox into the holder (C, Fig. 10a). You may also snap the
handbox into the holder: Slide one side of the handbox into the holder and then
firmly press the other side of the handbox into the holder until it snaps in place.
Adjust the tilt of of the holder by loosening the lock knob and then moving the
holder clamp to the desired angle. Retighten the lock knob.

A telescope’s eyepiece magnifies the image formed by the telescope’s main optics.
Each eyepiece has a focal length, expressed in millimeters, or “mm.” The smaller the
focal length, the higher the magnification. For example: An eyepiece with a focal
length of 9mm has a higher magnification than an eyepiece with a focal length of
26mm.

Your telescope comes supplied with a Series 5000 26mm 5-element Plössl eyepiece
which gives a wide, comfortable field of view with high image resolution.

Low power eyepieces offer a wide field of view, bright, high-contrast images, and eye
relief during long observing sessions. To find an object with a telescope, always start
with a lower power eyepiece such as the 26mm Plössl. When the object is located and
centered in the eyepiece, you may wish to switch to a higher power eyepiece to

A

B

C