Marantz bd8002 사용자 가이드
35
ENGLISH
SVENSKA
ITALIANO
ESPAÑOL
DEUTSCH
NEDERLANDS
FRANÇAIS
Speaker Setting
This unit allows you to enjoy multi-channel surround sound such as 7.1-channel / 5.1-channel
surround.
<Example of basic layout with 7.1ch surround system>
surround.
<Example of basic layout with 7.1ch surround system>
To make the most of its feature, set up your speakers appropriately by referring to the table below.
Speaker setting options are available at the following locations;
<Speaker setting for the audio signal output from the HDMI OUT jack >
(Available when you have HDMI cable connected to the HDMI OUT jack)
Setup
Speaker setting options are available at the following locations;
<Speaker setting for the audio signal output from the HDMI OUT jack >
(Available when you have HDMI cable connected to the HDMI OUT jack)
Setup
<Speaker setting for the audio signal output from the 7.1ch AUDIO OUT jacks >
Setup
Setup
How to navigate through the “HDMI Multi(LPCM)” and “Multi Channel” setting
1) Use [U / V] to select the menu item.
2) Use [U / V] to select setting items.
1) Use [U / V] to select the menu item.
2) Use [U / V] to select setting items.
• Use [RETURN] to go back to the previous screen.
3) Use [Y / Z] to select desired options.(Except for “Test Tone” and “Default”.)
• The test tone will be output. If you select “Manual”, use [U / V] to select desired speaker, then use
[Y / Z] to adjust the volume. If you select “Auto”, use [Y / Z] to adjust the volume of the speaker
that output the test tone.
that output the test tone.
• If you want to stop the test tone, press [RETURN].
Press [ENTER] to reset the “Delay Time” setting to the default.
4) Press [SETUP] to exit.
• For “Speaker Configuration”, the settings of each speaker sizes may be adjusted automatically
corresponding to each setting. (e.g. If the “Front” is set to “Small”, the “Subwoofer” will automatically
set to “On” and also you cannot set “Center”, “Surround”, and “Surround Back”, to “Large”.)
set to “On” and also you cannot set “Center”, “Surround”, and “Surround Back”, to “Large”.)
• If you connect to 5.1-channel surround system, set “Surround Back” in “Speaker Configuration” to
• “None” for “Center”, “Surround” and “Surround Back” is not available for the speaker setting for the
audio signal output from the HDMI OUT jack .
• “Off” for “Subwoofer” is not available for the speaker setting for the audio signal output from the
HDMI OUT jack.
Front speaker (left)
Front speaker (right)
Centre speaker
Subwoofer
Surround speaker (left)
Surround back speaker (left)
Surround speaker (right)
Surround back speaker (right)
Menu
Setting items
Options
Descriptions
Speaker Configuration
Select the desired
speaker to set. Then
change the setting
appropriately by
referring to the
descriptions.
Select the desired
speaker to set. Then
change the setting
appropriately by
referring to the
descriptions.
Large:
For the large speakers
with strong low frequency
reproduction capabilities.
Small:
For the small speakers
which do not provide
strong bass sound.
None:
No speakers.
For “Subwoofer” there is
only “On” or “Off”.
For the large speakers
with strong low frequency
reproduction capabilities.
Small:
For the small speakers
which do not provide
strong bass sound.
None:
No speakers.
For “Subwoofer” there is
only “On” or “Off”.
Crossover Freq:
For speakers set to
“Small”, the sound
with frequencies
below that of this
frequency are cut.
This bass sound that
has been cut is
output from the
subwoofer or a
speaker for which
“Large” is set.
For speakers set to
“Small”, the sound
with frequencies
below that of this
frequency are cut.
This bass sound that
has been cut is
output from the
subwoofer or a
speaker for which
“Large” is set.
40/60/80*/
100/120Hz
100/120Hz
Select according to the
low frequency
reproduction capabilities
of the connected speaker.
low frequency
reproduction capabilities
of the connected speaker.
E5J30ED_EN.book Page 35 Wednesday, October 15, 2008 9:32 PM