Danby dpac9009 사용자 가이드
OPERATING INSTRUCTIONS (cont’d)
AUTO-TIMER
The AUTO-TIMER feature offers a unique selection of multiple
choice, fully automatic on and/or off (start/stop) programs between
1-24 hours under any one mode of your Home Comfort unit.
choice, fully automatic on and/or off (start/stop) programs between
1-24 hours under any one mode of your Home Comfort unit.
The programs are as follows:
a) Auto-Off: Pre-select a time that will turn off the unit automatically (between 1-12hrs).
a) Auto-Off: Pre-select a time that will turn off the unit automatically (between 1-12hrs).
b) Auto-On: Pre-select a time that will turn on the unit automatically (between 1-12hrs).
c) Auto-On & Auto Off: Pre-select a time that will turn the unit ON / OFF automatically
at specified times (between 1-12hrs).
at specified times (between 1-12hrs).
Note: These functions must be performed daily, as the program is automatically
canceled/erased after the program has ended.
canceled/erased after the program has ended.
9
REMOTE CONTROL
FEATURES
Control Buttons:
1) Power Switch
2) Mode
3) Fan Speed
4) On / Off Timer
5) Time / Temperature Set
• Used for adjusting the timer and
temperature.
• The default display on control panel is
room temperature.
1) Power Switch
2) Mode
3) Fan Speed
4) On / Off Timer
5) Time / Temperature Set
• Used for adjusting the timer and
temperature.
• The default display on control panel is
room temperature.
• When
key is pressed in
cool mode, the set temperature is
displayed and may be adjusted. After 10
seconds the display will revert back to
room temperature.
• Timer setting is available from 1-24
hours by pressing the key
displayed and may be adjusted. After 10
seconds the display will revert back to
room temperature.
• Timer setting is available from 1-24
hours by pressing the key
To operate the hand held remote control
you will require two “AAA” Alkaline
batteries (included).
you will require two “AAA” Alkaline
batteries (included).
Batteries should be replaced when:
a) No signal (beep) is heard when attempting to program the main unit.
b) The main unit does not respond to a command issued by the remote control.
Battery replacement:
1) Slide the rear cover on the remote in the direction of the arrow. Continue pulling (gently)
until the cover separates completely from the unit.
2) Insert (2) batteries (AAA) following the same orientation (polarity) depicted inside the
battery chamber (+ / -).
3) Re-install rear cover.
4) If the remote control will not be used for extended periods of time (vacations, etc.),
batteries should be removed.
The remote operates within a range of 8 meters (26 ft.) from the receiver located inside
the main unit. Any obstruction between the receiver and remote may cause signal
interference, limiting the ability to program the unit.
a) No signal (beep) is heard when attempting to program the main unit.
b) The main unit does not respond to a command issued by the remote control.
Battery replacement:
1) Slide the rear cover on the remote in the direction of the arrow. Continue pulling (gently)
until the cover separates completely from the unit.
2) Insert (2) batteries (AAA) following the same orientation (polarity) depicted inside the
battery chamber (+ / -).
3) Re-install rear cover.
4) If the remote control will not be used for extended periods of time (vacations, etc.),
batteries should be removed.
The remote operates within a range of 8 meters (26 ft.) from the receiver located inside
the main unit. Any obstruction between the receiver and remote may cause signal
interference, limiting the ability to program the unit.
Notes:
1) Do not drop the remote control.
2) Do not place the remote control in a location exposed to direct sunlight.
3) The remote control should be placed about 1 meter or more away from TV, or any
electrical appliances.
1) Do not drop the remote control.
2) Do not place the remote control in a location exposed to direct sunlight.
3) The remote control should be placed about 1 meter or more away from TV, or any
electrical appliances.
This Class B digital apparatus complies with canadian ICES-003.