MemoRight 2.5" 32GB SATA SLC GT SSD MR25.2-032S 사용자 설명서
제품 코드
MR25.2-032S
MemoRight NAND Flash-based Solid State Drive
MemoRight Confidential
Page 26
3/6/2009
06 0 = SET FEATURES subcommand required to spin-up after
power-up not enabled
05 0 = Power-Up in Standby feature set not enabled
04 0 = Obsolete
03 1 = Advanced Power Management feature set enabled
02 0 = CFA feature set not supported
01 0 = READ/WRITE DMA QUEUED Command not supported
00 0 = DOWNLOAD MICROCODE Command not supported
power-up not enabled
05 0 = Power-Up in Standby feature set not enabled
04 0 = Obsolete
03 1 = Advanced Power Management feature set enabled
02 0 = CFA feature set not supported
01 0 = READ/WRITE DMA QUEUED Command not supported
00 0 = DOWNLOAD MICROCODE Command not supported
87
Command set/feature default
15 Shall be cleared to zero
14 Shall be set to one
13 1 = IDLE IMMEDIATE with UNLOAD FEATURE supported
12 0 = Reserved for Technical Report, INCITS TR-37-2004 (TLC)
11 0 = Reserved for Technical Report, INCITS TR-37-2004 (TLC)
10:9 0 = Obsolete
08 0 = 64-Bit World Wide Name not supported
07 0 = WRITE DMA QUEUED FUA EXT Command not supported
06 0 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT
commands not supported
05 0 = General Purpose Logging feature set not supported
04 0 = Obsolete
03 0 = Media Card Pass Through Command feature set not
supported
02 0 = Media Serial Number is not valid
01 1 = SMART Self-Test supported
00 1 = SMART Error-Logging supported
15 Shall be cleared to zero
14 Shall be set to one
13 1 = IDLE IMMEDIATE with UNLOAD FEATURE supported
12 0 = Reserved for Technical Report, INCITS TR-37-2004 (TLC)
11 0 = Reserved for Technical Report, INCITS TR-37-2004 (TLC)
10:9 0 = Obsolete
08 0 = 64-Bit World Wide Name not supported
07 0 = WRITE DMA QUEUED FUA EXT Command not supported
06 0 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT
commands not supported
05 0 = General Purpose Logging feature set not supported
04 0 = Obsolete
03 0 = Media Card Pass Through Command feature set not
supported
02 0 = Media Serial Number is not valid
01 1 = SMART Self-Test supported
00 1 = SMART Error-Logging supported
4003h
88
Ultra DMA modes
007Fh
89
Time required for security erase unit completion
XXXXh
90
Time required for Enhanced security erase unit completion(Not
support)
support)
0000h
91
Current advanced power management value
4080h
92
Master Password Revision Code
FFFEh
93
Hardware reset result
600Bh
94-99
Reserved
0000h
100-103
Maximum user LBA for 48-bit Address feature set
XXXXh
104-126
Reserved
0000h
127
Removable Media Status Notification feature set support
0000h
128
Security Status
0001h
129-159
Vendor specific
0000h
160
CFA power mode 1(Not support)
0000h
161-175
Reserved
0000h
176-205
Current media serial number
0000h
206-254
Reserved
0000h
255
CheckSum
XXXXh
5.2.32
Set Features (EFh)
This command is used by the host to establish or select certain features.
5.2.33
Set Features command
This command controls the implementation of various features that the drive supports. When the drive
receives this command, it sets BSY, checks the contents of the Features register, clears BSY and
generates an interrupt. If the value in the register does not represent a feature that the drive supports,
the command is aborted. Power-on default has the read look-ahead and writes caching features
enabled. The acceptable values for the Features register are defined as follows:
receives this command, it sets BSY, checks the contents of the Features register, clears BSY and
generates an interrupt. If the value in the register does not represent a feature that the drive supports,
the command is aborted. Power-on default has the read look-ahead and writes caching features
enabled. The acceptable values for the Features register are defined as follows: