ZyXEL p-660h-61 사용자 가이드
Prestige 660H Series User’s Guide
Internet Access
24-5
Table 24-2 Menu 4 Internet Access Setup
FIELD DESCRIPTION
EXAMPLE
ISP’s Name
Enter the name of your Internet Service Provider. This information is for
identification purposes only.
identification purposes only.
MyIsp
Encapsulation
Press [
SPACE BAR
] to select the method of encapsulation used by
your ISP. Choices are PPPoE, PPPoA, RFC 1483 or ENET ENCAP.
ENET ENCAP
Multiplexing
Press [
SPACE BAR
] to select the method of multiplexing used by your
ISP. Choices are VC-based or LLC-based.
LLC-based
VPI #
Enter the Virtual Path Identifier (VPI) assigned to you.
8
VCI #
Enter the Virtual Channel Identifier (VCI) assigned to you.
32
ATM QoS Type
Press [SPACE BAR] and select CBR (Continuous Bit Rate) to specify
fixed (always-on) bandwidth. Select UBR (Unspecified Bit Rate) for
applications that are non-time sensitive, such as e-mail. Select VBR
(Variable Bit Rate) for bursty traffic and bandwidth sharing with other
applications.
fixed (always-on) bandwidth. Select UBR (Unspecified Bit Rate) for
applications that are non-time sensitive, such as e-mail. Select VBR
(Variable Bit Rate) for bursty traffic and bandwidth sharing with other
applications.
UBR
Peak Cell Rate
(PCR)
(PCR)
This is the maximum rate at which the sender can send cells. Type the
PCR.
PCR.
0
Sustain Cell Rate
(SCR)= 0
(SCR)= 0
Sustained Cell Rate is the mean cell rate of a bursty, on-off traffic source
that can be sent at the peak rate, and a parameter for burst-traffic. Type
the SCR; it must be less than the PCR.
that can be sent at the peak rate, and a parameter for burst-traffic. Type
the SCR; it must be less than the PCR.
0
Maximum Burst
Size (MBS)= 0
Size (MBS)= 0
Refers to the maximum number of cells that can be sent at the peak rate.
Type the MBS. The MBS must be less than 65535.
Type the MBS. The MBS must be less than 65535.
0
My Login
Configure the My Login and My Password fields for PPPoA and PPPoE
encapsulation only. Enter the login name that your ISP gives you. If you
are using PPPoE encapsulation, then this field must be of the form
user@domain where domain identifies your PPPoE service name.
encapsulation only. Enter the login name that your ISP gives you. If you
are using PPPoE encapsulation, then this field must be of the form
user@domain where domain identifies your PPPoE service name.
N/A
My Password
Enter the password associated with the login name above.
N/A
ENET ENCAP
Gateway
Gateway
Enter the gateway IP address supplied by your ISP when you are using
ENET ENCAP encapsulation.
ENET ENCAP encapsulation.
N/A
Idle Timeout
This value specifies the number of idle seconds that elapse before the
Prestige automatically disconnects the PPPoE session.
Prestige automatically disconnects the PPPoE session.
0
IP Address
Assignment
Assignment
Press [
SPACE BAR
] to select Static or Dynamic address assignment.
Dynamic
IP Address
Enter the IP address supplied by your ISP if applicable.
N/A
Network Address
Translation
Translation
Press [
SPACE BAR
] to select None, SUA Only or Full Feature.
Please see the NAT Chapter for more details on the SUA (Single User
Account) feature.
Account) feature.
SUA Only
Address
Mapping Set
Mapping Set
Type the numbers of mapping sets (1-8) to use with NAT. See the NAT
chapter for details.
chapter for details.
N/A
When you have completed this menu, press [ENTER] at the prompt “Press ENTER to confirm or ESC to cancel” to
save your configuration or press [ESC] to cancel and go back to the previous screen.
save your configuration or press [ESC] to cancel and go back to the previous screen.
If all your settings are correct, your Prestige should connect automatically to the Internet. If the
connection fails, note the error message that you receive on the screen and take the appropriate
troubleshooting steps.
connection fails, note the error message that you receive on the screen and take the appropriate
troubleshooting steps.