JVC GR-DX307 지침 매뉴얼

MasterPage: Left

Rewind the tape in the camcorder to the beginning 

of the scene you want to edit and press PAUSE (9).

Press VCR REC STBY (79) on the remote control, 

or manually engage the VCR’s Record-Pause mode.

Press the Recording Start/Stop Button on the 

camcorder. Editing proceeds as programmed, right 
through to the end of the last registered scene.

● When dubbing is complete, the camcorder enters the 

Pause mode, and the VCR enters its Record-Pause mode.

● If you do not register an Edit-Out point, the tape will be 

dubbed all the way to the end automatically.

● If you operate the camcorder during automatic editing, the 

VCR will enter its Record-Pause mode and automatic 
editing will stop.

Engage the Stop modes for the camcorder and the 

VCR.

● To make the R.A.Edit counter display disappear, press 

R.A.EDIT ON/OFF on the remote control.

● Pressing R.A.EDIT ON/OFF on the remote control clears 

all settings registered during Random Assemble Editing.

● When the editing cable is connected to the remote control’s 

PAUSE IN connector during dubbing, make sure the remote 
control is pointed at the VCR’s sensor, and the path 
between the two is unobstructed.

● Random Assemble Editing may not function properly when 

using a tape including several duplicated time codes. 
(

Some VCRs make the transition from Record-Pause to 
Record mode faster than others. Even if you begin 
editing for the camcorder and the VCR at exactly the 
same time, you may lose scenes you wanted, or find that 
you have recorded scenes you did not want. For a cleanly 
edited tape, confirm and adjust the timing of the 
camcorder against your VCR.

Play back the tape in the camcorder, then point the 

remote control at the camcorder’s remote sensor and 
press R.A.EDIT ON/OFF.

● Random Assemble Editing Menu 

appears. 

Perform Random Assemble 

Editing on Program 1 only. In order 
to check VCR and camcorder 
timing, select the beginning of a 
scene transition as your Edit-In 
point.

Play back the dubbed scene.

● If any images from the scene prior to the transition you 

chose for your Edit-In point were recorded, that means your 
VCR moves too quickly from Record-Pause to Record 
mode.

● If the scene you tried to dub starts in progress, the VCR is 

slow to start recording.

Press R.A.EDIT ON/OFF to make the Random 

Assemble Editing menu disappear, then press MENU. 
The Menu Screen appears.

Press SET to select “t”. The VIDEO Menu appears. 

Press 

 or 

 to select “SYNCHRO”, and press SET. 

The value for “SYNCHRO” is highlighted. (Factory-
preset: ±0.0)

Based on the diagnostics performed, you can now 

advance the VCR’s record timing by pressing 

. You 

can also delay the VCR’s record timing by pressing 

.

● The adjustment range is from –1.3 to +1.3 seconds, in 0.1-

second increments.

Press SET to finish the setting.

Press 

 or 

 to select “BRETURN”, and press SET 

twice.

● Now perform Random Assemble Editing beginning with 

step 

6 on page 43.

● Before performing actual Random Assemble Editing, do a 

few Random Assemble Editing trial runs to check whether 
the value you have input is appropriate or not, and make 
adjustments accordingly.

● Depending on the recorder, there may be situations where 

the timing difference cannot be fully corrected.

GR-DX307US.book  Page 44  Monday, April 19, 2004  6:41 PM