Hitachi 20gn 설치 설명서
Handling precautions
!
Wear a wrist strap while handling the drive to pre-
vent damage from Electrostatic Discharge (ESD).
vent damage from Electrostatic Discharge (ESD).
!
Set the drive down gently to prevent damage from
impact or vibration.
impact or vibration.
!
Do not open the ESD bag containing the drive until
needed.
needed.
!
Handle the drive carefully by the edges. Do not
touch the exposed printed circuit board or any
electronic components.
touch the exposed printed circuit board or any
electronic components.
!
Do not press on the top or bottom of the drive.
!
Do not cover the drive’s breather hole.
Quick installation*
IMPORTANT: Back up all data before proceeding with
installation.
installation.
*It is important to note that the use of Travelstar drives in
some notebooks will require reuse of unique hardware
(for example — mounting trays, connecting cable,
insulating material). If in doubt please consult your
notebook manufacturer as this operation may require a
qualified technician.
Set the jumpers
some notebooks will require reuse of unique hardware
(for example — mounting trays, connecting cable,
insulating material). If in doubt please consult your
notebook manufacturer as this operation may require a
qualified technician.
Set the jumpers
!
Master drive. No jumpers are required if the drive is
the only drive in a system or the Master drive in a
two-drive system. See setting A1 opposite.
the only drive in a system or the Master drive in a
two-drive system. See setting A1 opposite.
!
Slave drive. If the drive is the Slave drive in a two-
drive system, jumper setting A2 (see opposite) is
required.
drive system, jumper setting A2 (see opposite) is
required.
!
Cable Select. Consult the system manual to see if
your computer supports Cable Select before choos-
ing the A3 jumper setting
your computer supports Cable Select before choos-
ing the A3 jumper setting
.
Attach the drive
Consult your system manual for instructions on how to
complete the physical installation of the drive.
Consult your system manual for instructions on how to
complete the physical installation of the drive.
Jumper settings
A1.
A2.
A3.
A4.
A5.
Pin 1
djsa_qi1.prz
A1. Master
A2. Slave
A3. Cable Select
A4. Never Attach a Jumper Here
A5. Never Attach a Jumper Here
A2. Slave
A3. Cable Select
A4. Never Attach a Jumper Here
A5. Never Attach a Jumper Here
Configure your computer
1. Turn on your computer. Your computer may detect a
1. Turn on your computer. Your computer may detect a
configuration change and prompt you to proceed to
the Setup screen.
the Setup screen.
2. If your computer does not prompt you to reconfigure,
enter your computer’s Setup, typically by key
selection or keyboard combinations during power-on
or during a reboot. Refer to your system manual for
the proper key sequence. If the computer fails to boot
up, power off, remove the drive, and return your
system to its original configuration. Reboot and enter
your computer’s Setup. Follow the directions in
step 3, then attach the drive.
selection or keyboard combinations during power-on
or during a reboot. Refer to your system manual for
the proper key sequence. If the computer fails to boot
up, power off, remove the drive, and return your
system to its original configuration. Reboot and enter
your computer’s Setup. Follow the directions in
step 3, then attach the drive.
3. Select Auto Detect if your computer Setup supports
this feature. If your computer does not support Auto
Detect, select the appropriate UDT (User Definable
Type) for the drive.
Detect, select the appropriate UDT (User Definable
Type) for the drive.
ibm
Quick installation guide
Travelstar 32GH, 30GT & 20GN
2.5 inch ATA/IDE hard disk drive
DJSA-205
DJSA-220
DJSA-210
DJSA-210
DJSA-232
DJSA-230
DJSA-230
Models:
IBM storage products
Page 1
IBM Technology Group Support Center version 2.0