Hitachi 18es 설치 설명서
Quick installation guide
Ultrastar 18ES
Single-ended/multi-mode SE/LVD
Models: DNES-318350
DNES-309170
DNES-309170
IBM storage products
Page 1
IBM Hard Disk Drive Technical Support Center version 2.0
Handling precautions
1. Do not cover the breather hole! Covering the
breather hole may result in loss of
breather hole may result in loss of
data.
2. Do not press on the drive! Do not apply any force
to the drive during handling or installation.
to the drive during handling or installation.
3. Always handle the drive with care to prevent
damage from shock, vibration, or electrostatic
discharge (ESD).
4. Do not open the static-protective bag containing
the drive until required. Static electricity can damage
the drive.
5. Turn off and unplug your computer before
removing the case.
6. When you are installing the drive, touch the
static-protective package containing the drive to a
grounded, unpainted metal surface for at least two
seconds. (This drains static electricity from the
package and from your body.)
7. Handle the drive carefully by the edges. Do not
touch any exposed printed circuit board.
8. Save your drive packaging materials including the
ESD bag in the event that the drive must be returned.
Place the drive in an anti-static bag before placing it in
the shipping container. The warranty will be void if
the drive is not returned in IBM approved packaging
damage from shock, vibration, or electrostatic
discharge (ESD).
4. Do not open the static-protective bag containing
the drive until required. Static electricity can damage
the drive.
5. Turn off and unplug your computer before
removing the case.
6. When you are installing the drive, touch the
static-protective package containing the drive to a
grounded, unpainted metal surface for at least two
seconds. (This drains static electricity from the
package and from your body.)
7. Handle the drive carefully by the edges. Do not
touch any exposed printed circuit board.
8. Save your drive packaging materials including the
ESD bag in the event that the drive must be returned.
Place the drive in an anti-static bag before placing it in
the shipping container. The warranty will be void if
the drive is not returned in IBM approved packaging
.
Installation procedure
Note: It is advisaable to backup all data before pro-
ceeding with the installation.
ceeding with the installation.
This procedure may require the use of a bootable
System Diskette containing FDISK.COM and
FORMAT.COM.
System Diskette containing FDISK.COM and
FORMAT.COM.
Setting the address
1. Each drive on the SCSI bus must have a unique
address. Sixty eight and eighty pin (Wide SCSI)
devices have 16 possible addresses.
2. SCSI address bits 3,2,1, and 0 of the 32 pin Option
Jumper Block are used to select the SCSI device ID.
1. Each drive on the SCSI bus must have a unique
address. Sixty eight and eighty pin (Wide SCSI)
devices have 16 possible addresses.
2. SCSI address bits 3,2,1, and 0 of the 32 pin Option
Jumper Block are used to select the SCSI device ID.
G F E D C B A
12 11 10 9 8 7 6 5 4 3 2 1
Reserved
Open
Enable Terminator
Power Supply
Power Supply
0 1 2 3
SCSI ID Bits
SCSI ID Bits
Enable Auto Spin Up
Disable Unit Attention
Enable TI-SDTR/WDTR
Enable Auto Start Delay
Delay Start 6/12
Disable SCSI Parity Check
LED Cathod
Ground
Ground
Open
SCSI Bus
LED Anode
Enable SCSI Terminator
*80 pin models do not have Option Jumper Block J-6
*Position #6 is "Force Single-ended Mode" on multi-mode SE/LVD
models.
*Position #6 is "Force Single-ended Mode" on multi-mode SE/LVD
models.
Option Jumper Block J-4 Option Jumper Block J-6