Manualsbrain.com
  1. 매뉴얼
  2. 브랜드
  3. Clavia
  4. electro 3
  5. 사용자 가이드

Clavia electro 3 사용자 가이드

다운로드
페이지 중 27
Program and Controller dumps
To dump a Program SysEx, or MIDI Controller data via MIDI, either 
to another Nord Electro 3 or for recording the data into another MIDI 
device, proceed as follows:
Sending program dumps
Connect the MIDI OUT on the Nord Electro 3 to the MIDI In on the 
1
receiving device .
Set up the receiving device to accept MIDI SysEx and MIDI Con-
2
troller data .
Press Shift + MIDI and select the “Dump One” or “Dump All” menu 
3
item using the Up/Down buttons .
If needed, set the receiving MIDI device to “recording mode” .
4
Press the Store button to send the dump to the MIDI Out of Nord 
5
Electro 3 . The display will stop flashing once the dump has been 
sent .
For the programs that use the organ sounds, the complete 
 
M
settings for the sound will be dumped as MIDI SysEx but for 
programs using pianos or Samples, all parameters will be sent but 
NOT the actual instrument samples.
Therefore, when dumping back a program that uses a piano sound, 
make sure the actual instrument samples are also available in the Nord 
Electro 3 . Otherwise the parameters in the SysEx message will be ap-
plied to another available piano instrument .
Sending MIDI Controller dumps
Set up as in steps 1 and 2 in the preceding description .
1
Press Shift + MIDI and select the ‘Send CC” menu item using the 
2
Up/Down buttons .
Press the Store button to send the dump to the MIDI Out of Nord 
3
Electro 3 . The Display will stop flashing once the dump has been 
sent .
Receive MIDI SysEx dumps
Here is how to receive a MIDI SysEx Dump:
Connect the MIDI Out on the transmitting device to the MIDI IN on 
1
the Nord Electro 3 .
Initiate the transmission on the transmitting device .
2
If the dump contained all Programs (All), it will replace all programs 
currently stored in the Nord Electro 3 . If the dump contained only a 
single program, it will be temporarily placed in the currently selected 
program memory location . A dot will appear to in the lower, right corner 
to indicate an unsaved edit . You will then have to store the program 
manually to a memory location using the Store function (see “Storing 
Programs” on page 8) .
MIDI Controller list
The following is a list of the MIDI Controller numbers used for all knobs 
and buttons on the front panel:
Nord Electro Parameter
MIDI  
Controller
Drawbars - Preset 2/Upper
Drawbar 1 
16
Drawbar 2
17
Drawbar 3
18
Drawbar 4
19
Drawbar 5
20
Drawbar 6
21
Drawbar 7
22
Drawbar 8
23
Drawbar 9
24
Drawbars - Preset 1/Lower
Drawbar 1
70
Drawbar 2
71
Drawbar 3
72
Drawbar 4
73
Drawbar 5
74
Drawbar 6
75
Drawbar 7
 76
Drawbar 8
77
Drawbar 9
78
Organ Model Sel
9
Preset/Manual Sel
3
Perc Decay
88
Perc Level
89
Sustain Pedal
64
Control Pedal
11
Rotary Speed
82
Rotary Stop Mode
79
Vib Mode
84
Vib On/Off Preset 2/UP
85
Vib On/Off Preset 1/LOW (B3 model)
117
Perc On/Off
87
Perc Hard
95
Samp Attack Sel
33
Samp Release Sel
34
Clav EQ Brill On/Off
103
Clav EQ Treble On/Off
104
Clav EQ Medium On/Off
105
Clav EQ Soft On/Off
106
Inst Sel (Organ/Piano)
13
Piano Type
12
Piano Model
44
Piano Mono
83
Oct Shift Organ Upper
27
Oct Shift Organ Lower
28
Oct Shift Piano
29
EQ On/Off
115
EQ Treble
113
EQ Mid
116
EQ Mid Freq
117
EQ Bass
114
Gain
7
Effect 1 Rate
63
Effect 1 Sel
60
Effect 1 On/Off
69
Effect 2 Rate
62
Effect 2 Sel
61
Effect 2 On/Off
80
Speaker/Comp Drive
111
Speaker/Comp Sel
81
Speaker/Comp On/Off
86
Reverb Wet/Dry
102
Reverb Sel
96
Reverb On/Off 
97
24 | NordElEctro3UsErMaNUalosv3.x