Canon iPF8400 매뉴얼
Cause
Corrective Action
The Release Lever is up. If the error occurs again, turn off the printer and wait a while before restoring power.
Rewinding error.
Rewinding error.
Cause
Corrective Action
There is some foreign object near the Media Take-up Unit sensor and
the roll cannot be detected.
the roll cannot be detected.
Remove the foreign object near the sensor.
The Media Take-up Unit sensor is soiled and the roll cannot be detec-
ted.
ted.
Wipe the sensor with a dry cloth to clean it.
The roll is out of range of detection by the Media Take-up Unit sensor.
Reload the roll.
Press the OK button to clear the error.
Press the OK button to clear the error.
A paper jam has occurred and the roll cannot be rewound.
Remove the paper from the Media Take-up Unit.
Press the OK button to clear the error.
Press the OK button to clear the error.
The Media Take-up Unit sensor is damaged.
Contact your Canon dealer for assistance.
*1: Printing will stop momentarily if an error involving the Media Take-up Unit occurs. If you prefer printing not to stop, set Skip Take-Up Err
to On. However, note that this error may cause paper jams and affect the printing quality.
Media take-up unit ready.
Media take-up unit ready.
Cause
Corrective Action
The Take-up Reel setting in the printer Set./Adj. Menu was
changed from Enable to Disable, but a print job was re-
ceived before the roll was removed.
changed from Enable to Disable, but a print job was re-
ceived before the roll was removed.
Press ▲ or ▼ to select Stop Printing, and then press the OK button to stop
printing.
The mode switches from take-up mode to regular mode after you change the
Take-up Reel setting in the Set./Adj. Menu from Enable to Disable and lift the
Release Lever to remove a roll, or after you execute Paper Cutting.
printing.
The mode switches from take-up mode to regular mode after you change the
Take-up Reel setting in the Set./Adj. Menu from Enable to Disable and lift the
Release Lever to remove a roll, or after you execute Paper Cutting.
Press ▲ or ▼ to select Print, and then press the OK button to resume printing.
Turn on the media take-up unit.
Turn on the media take-up unit.
Cause
Corrective Action
The Take-up Reel setting in the control panel menu was changed to Enable while the power to the
Take-up Reel was off and the Roll Media lamp on the control panel was lit.
Take-up Reel was off and the Roll Media lamp on the control panel was lit.
Turn the Media Take-up Unit on.
The Take-up Reel setting in the control
panel menu changes to Disable.
panel menu changes to Disable.
Borderless printng not possible.
Borderless printng not possible.
Cause
Corrective Action
The print job received specifies a type
or width of paper that is not compatible
with borderless printing.
or width of paper that is not compatible
with borderless printing.
Follow these steps to change the settings of the print job to enable borderless printing.
1.
Press ▲ or ▼ to select Stop Printing, and then press the OK button.
2.
Make sure the correct printer driver for the printer is selected and try printing again.
For information on types of paper compatible with borderless printing, refer to the Paper Refer-
ence Guide.
For information on types of paper compatible with borderless printing, refer to the Paper Refer-
ence Guide.
(See "Paper Reference Guide.")
Select None when you have set Detect Mismatch on the control panel to Warning.
However, note that this error may cause paper jams and affect the printing quality.
However, note that this error may cause paper jams and affect the printing quality.
Press ▲ or ▼ to select Print With Border, and then press the OK button to continue printing. The
document will be printed with a border.
document will be printed with a border.
The loaded paper is a size not compat-
ible with borderless printing.
ible with borderless printing.
Press ▲ or ▼ to select Stop Printing, and then press the OK button.
Replace the paper with paper compatible for borderless printing as follows.
Rewinding error.
iPF8400
Error Message
Messages regarding paper
1000