Canon ip3000 설치 설명서
Install the Ink Tanks
Unpack the Printer
1
2
3
4
5
Prepare the Printer
Install the Print Head
Connect the Printer
and Load Paper
Start Here
Easy Setup Instructions
iP3000
Series
Photo Printer
Insert the ink tank into the correct slot.
(Refer to the color guide on the print head holder).
(Refer to the color guide on the print head holder).
Press down until the ink tank clicks into place.
Paper Support
Top Cover
Paper Output Tray
Inner Cover
Remove the shipping tape from the paper
guide. Pinch the paper guide and slide it to
the left. Load a few sheets of blank paper
into the auto sheet feeder, then slide the
paper guide toward the left edge of the paper.
guide. Pinch the paper guide and slide it to
the left. Load a few sheets of blank paper
into the auto sheet feeder, then slide the
paper guide toward the left edge of the paper.
3
Paper
Guide
Guide
Auto Sheet
Feeder
Slide the print head into the holder.
The print head will rest at a slight angle.
The print head will rest at a slight angle.
Remove the print head from its package.
Remove the orange protective cap
from the print head.
from the print head.
NOTE: Do not touch the print head nozzles
and the electrical contacts.
and the electrical contacts.
Lower the print head lock lever and press
it down until it clicks into place.
it down until it clicks into place.
Raise the print head lock lever.
Electrical Contacts
Print Head Nozzles
Tear at notch to open
Plug the power cord into the back of the
printer and connect the other end to a
power outlet. Press the POWER button.
The printer will initialize.
printer and connect the other end to a
power outlet. Press the POWER button.
The printer will initialize.
Lower the front cover. Raise the top cover.
Remove the shipping tape and lower the
inner cover.
Remove the shipping tape and lower the
inner cover.
The print head holder automatically moves
to the center. Remove the protective tape.
to the center. Remove the protective tape.
Write down the serial number located to
the right of the print head holder . You will
need this later to register the product.
the right of the print head holder . You will
need this later to register the product.
Remove the shipping tape from the
front and back of the printer.
front and back of the printer.
POWER
Button
POWER
Lamp
Serial Number
Protective Tape
Inner Cover
Top Cover
Front Cover
PIXMA iP3000 Series
Photo Printer
Carefully remove all items from the box.
Documentation
and Software Kit
Peel back the orange tab and completely
remove the plastic wrapper from the Yellow
Ink Tank (BCI-6Y).
remove the plastic wrapper from the Yellow
Ink Tank (BCI-6Y).
Twist off and discard the orange protective cap.
Insert the remaining three ink tanks into
their assigned slots.
their assigned slots.
Close the inner cover, then the top cover.
Lift open the paper support and extend the
paper output tray.
Lift open the paper support and extend the
paper output tray.
Power Cord
PIXMA iP3000 Series
Print Head
NOTE: The printer will perform a print head
cleaning. Wait until the POWER lamp displays
a steady green light before proceeding.
a steady green light before proceeding.
Ink Tanks
BCI-6C Cyan BCI-6M Magenta
BCI-3eBK Black BCI-6Y Yellow
click
click
Continue with Step 6
on side two.
on side two.
NOTE: To avoid spilling ink, never press on the
sides of an ink tank.
Protective Cap
IMPORTANT: Be sure the printer is
off before continuing, or the computer
will attempt to install the printer
driver before the printer is ready.
off before continuing, or the computer
will attempt to install the printer
driver before the printer is ready.
TURN THE PRINTER OFF.
Connect one end of the USB cable
to the computer, the other to the printer.
to the computer, the other to the printer.
1
2
1
2
3
4
5
1
5
4
3
1
2
1
2
3
4
5
Serial Number
Location