ONKYO ht-s5600 사용자 가이드
Advanced Operations
En-39
Menu
Digital Audio
If you connect a component to a digital audio input, you
must assign that input to an input selector. For example, if
you connect your CD player to the COAXIAL IN 1, you
must assign “COAXIAL1” to the “TV/CD” input selector.
Here are the default assignments.
must assign that input to an input selector. For example, if
you connect your CD player to the COAXIAL IN 1, you
must assign “COAXIAL1” to the “TV/CD” input selector.
Here are the default assignments.
■
BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,
TV/CD
TV/CD
`
COAXIAL1, COAXIAL2, OPTICAL:
Select the input to which the component has been
connected.
connected.
`
- - - - -:
Select if the component is connected to an analog
audio input.
audio input.
Note
• When an HDMI IN is assigned to an input selector in
“HDMI Input” (
), the same HDMI IN will be set as
a priority in this assignment. In this case, if you want to use the
coaxial or optical audio input, make the appropriate selection in
the “Audio Selector” (
coaxial or optical audio input, make the appropriate selection in
the “Audio Selector” (
).
• Supported sampling rates for PCM signals (stereo/mono) from a
digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16,
20, 24 bit.
20, 24 bit.
Menu
Sp Config
Here you can check the settings made by Audyssey 2EQ
Room Correction and Speaker Setup, or set them manually,
which is useful if you change one of the connected
speakers after using Audyssey 2EQ Room Correction and
Speaker Setup.
This section explains how to specify which speakers are
connected and their sizes.
Room Correction and Speaker Setup, or set them manually,
which is useful if you change one of the connected
speakers after using Audyssey 2EQ Room Correction and
Speaker Setup.
This section explains how to specify which speakers are
connected and their sizes.
For speakers with a cone diameter larger than 6-1/2 inches
(16 cm), specify Large (full band). For those with a
smaller diameter, specify Small (default crossover
100 Hz).
The crossover frequency can be changed in the “Crossover
(Crossover Frequency)” (
(16 cm), specify Large (full band). For those with a
smaller diameter, specify Small (default crossover
100 Hz).
The crossover frequency can be changed in the “Crossover
(Crossover Frequency)” (
).
Note
• These settings are not available in either of the following cases:
– A pair of headphones is connected.
– The “Audio TV Out” setting is set to “On” (
– The “Audio TV Out” setting is set to “On” (
– “HDMI CEC (RIHD)” is set to “On” (
) and
you’re listening through your TV speakers.
■
Powered Zone 2
`
No
`
Yes:
Zone 2 speakers can be used. (Powered Zone 2
enabled).
enabled).
Note
• When the “Powered Zone 2” setting is set to “Yes” and Zone 2
is turned on, the surround back and front high speakers cannot be
used.
used.
■
Subwoofer
`
Yes
`
No
■
Front
`
Small
`
Large:
Select based on the cone diameter.
Note
• If the “Subwoofer” setting is set to “No”, this setting is fixed to
“Large”.
■
Center
`
Small
`
Large:
Select based on the cone diameter.
`
None
■
Front High
`
Small
`
Large:
Select based on the cone diameter.
`
None
■
Surround Back
`
Small
`
Large:
Select based on the cone diameter.
`
None
3. Digital Audio (Digital Audio Input)
Input selector
Default assignment
BD/DVD
COAXIAL1
VCR/DVR
- - - - -
CBL/SAT
COAXIAL2
GAME
- - - - -
AUX
- - - - -
TV/CD
OPTICAL
1
2
3
4
5
6
4. Sp Config (Speaker Configuration)
Some of the settings in this section are set automatically
by Audyssey 2EQ
by Audyssey 2EQ
®
Room Correction and Speaker Setup
).
1
2
3
4
5
6
Cone diameter