ONKYO ht-s5600 사용자 가이드
Advanced Operations
En-45
.
Menu
Hardware
OSD
■
Volume OSD
`
On
`
Off
Turn this setting on to display the volume level on the TV
screen while it is adjusted.
screen while it is adjusted.
Remote ID
■
Remote ID
`
1, 2, or 3
When several Onkyo components are used in the same
room, their remote ID codes may overlap. To differentiate
the AV receiver from the other components, you can
change its remote ID from “1”, to “2” or “3”.
room, their remote ID codes may overlap. To differentiate
the AV receiver from the other components, you can
change its remote ID from “1”, to “2” or “3”.
Note
• If you do change the AV receiver’s remote ID, be sure to change
the remote controller to the same ID (see below), otherwise, you
won’t be able to control it with the remote controller.
won’t be able to control it with the remote controller.
Changing the remote controller’s ID
Tuner
■
AM/FM Freq Step (North American, Brazilian and
Taiwanese models)
Taiwanese models)
`
10kHz/200kHz:
`
9kHz/50kHz:
Select the frequency step according to your area.
■
AM Freq Step (Asian models)
`
10kHz:
`
9kHz:
Select the frequency step according to your area.
For AM/FM tuning to work properly, you must specify the
AM/FM frequency step used in your area.
AM/FM frequency step used in your area.
Note
• When this setting is changed, all radio presets will be deleted.
Auto Standby
■
Auto Standby
`
Off
`
On
When “Auto Standby” is set to “On”, the AV receiver
will automatically enter standby mode if there is no
operation for 30 minutes with no audio and no video signal
input.
“Auto Standby” will appear on the AV receiver’s display
and OSD 30 seconds before the Auto Standby comes on.
Default setting: On (Asian models), Off (North
American, Brazilian and Taiwanese models)
will automatically enter standby mode if there is no
operation for 30 minutes with no audio and no video signal
input.
“Auto Standby” will appear on the AV receiver’s display
and OSD 30 seconds before the Auto Standby comes on.
Default setting: On (Asian models), Off (North
American, Brazilian and Taiwanese models)
Note
• Set to “
On”
, the Auto Standby function may activate itself during
playback with some sources.
• The Auto
Standby function does not work when Zone 2 is on.
■
HDMI Through
`
Off
`
On
This setting enables or disables the Auto Standby during
HDMI Through by detecting the audio/video input signal.
When this setting is set to “On”, the AV receiver will
automatically enter standby mode if there is no audio and
no video signal input during HDMI Through for 30
minutes.
When this setting is set to “Off”, the status of HDMI
Through is continued regardless of audio/video input
signal.
HDMI Through by detecting the audio/video input signal.
When this setting is set to “On”, the AV receiver will
automatically enter standby mode if there is no audio and
no video signal input during HDMI Through for 30
minutes.
When this setting is set to “Off”, the status of HDMI
Through is continued regardless of audio/video input
signal.
Tip
• Entering standby mode is possible by setting “HDMI CEC
(RIHD)” to “On” and using CEC-compatible component
regardless of the above-mentioned setting.
See “HDMI CEC (RIHD)” in “10. HDMI Setup” for linked
operation.
regardless of the above-mentioned setting.
See “HDMI CEC (RIHD)” in “10. HDMI Setup” for linked
operation.
• When the HDMI Through is enabled, the power consumption
slightly increases.
Note
• This setting is fixed to “Off” when “Auto Standby” is set to
“Off”.
9. Hardware
1
While holding down
RECEIVER, press and hold
down
SETUP until the remote indicator lights
(about 3 seconds).
2
Use the number buttons to enter ID 1, 2, or 3.
The remote indicator flashes twice.
The remote indicator flashes twice.
1
2
3
4
5
6