Samsung dvd-v940 지침 매뉴얼
ENG-9
Deck Control Keys
The DVD-VCR uses one set of controls to operate both
decks. The following keys are helpful in successfully
controlling each deck.
decks. The following keys are helpful in successfully
controlling each deck.
1
STANDBY/ON Button
Press the STANDBY/ON button on the remote
control or front panel to turn on the DVD-VCR.
Press the STANDBY/ON button on the remote
control or front panel to turn on the DVD-VCR.
2
DVD Button
Press the DVD button on the remote control when
you want to control the DVD deck.
Press the DVD button on the remote control when
you want to control the DVD deck.
◆
The DVD indicator will light on the Front
Panel Display to show that the DVD deck is
selected.
Panel Display to show that the DVD deck is
selected.
3
VCR Button
Press the VCR button on remote control when you
want to control the VCR deck.
Press the VCR button on remote control when you
want to control the VCR deck.
◆
The VCR indicator will light on the Front Panel
Display to show that VHS deck is selected.
Display to show that VHS deck is selected.
4
INPUT SEL. Button
Press the INPUT SEL. button repeatedly to cycle
through all of your input sources, including the
Tuner (PR##), Line 1 (rear AV input).
Press the INPUT SEL. button repeatedly to cycle
through all of your input sources, including the
Tuner (PR##), Line 1 (rear AV input).
➢
Before using the VCR operation of 11~26 pages,
press the VCR button on the remote control to
select VCR mode.
press the VCR button on the remote control to
select VCR mode.
Before using the DVD operation of 27~45 pages,
press the DVD button on the remote control to
select and watch DVD.
press the DVD button on the remote control to
select and watch DVD.
Tuning Your Television for the
DVD-VCR
DVD-VCR
You must tune your television for the DVD-VCR only if
you are not using a A/V cable
you are not using a A/V cable
➢
To view pictures from your DVD-VCR when a
A/V cable is used, the television must be set to
the audio/video mode (AV).
A/V cable is used, the television must be set to
the audio/video mode (AV).
1
Switch on the television.
2
Switch on the DVD-VCR by pressing STANDBY/ON
on the front of the DVD-VCR or STANDBY/ON on
the remote control.
on the front of the DVD-VCR or STANDBY/ON on
the remote control.
3
Select a programme position on the television to be
reserved for use with your DVD-VCR.
reserved for use with your DVD-VCR.
4
Insert the video cassette in the DVD-VCR. Check
that the DVD-VCR starts reading the cassette; if
not, press
that the DVD-VCR starts reading the cassette; if
not, press
❿
II
button.
5
Start a scan on your television or set the television
to UHF channel 38.
to UHF channel 38.
6
Fine tune the television until the pictures and sound
are obtained clearly.
are obtained clearly.
7
If you cannot find the pictures and sound, or there
is interference from nearby channels, it may be
necessary to change the setting of the DVD-VCR
output channel (see Setting the DVD-VCR Output
Channel on page 14 and Problems and Solutions
on page 47).
is interference from nearby channels, it may be
necessary to change the setting of the DVD-VCR
output channel (see Setting the DVD-VCR Output
Channel on page 14 and Problems and Solutions
on page 47).
8
When the picture and sound are perfectly clear,
store this channel at the desired programme
position on the television.
Result: That programme is now reserved for use
store this channel at the desired programme
position on the television.
Result: That programme is now reserved for use
with your DVD-VCR.
00374R DVD-V940K/XSA-ENG 5/6/04 11:34 AM Page 9