Epson 5600p 제품 데이터시트
EPSON PowerLite 5600p and 7600p Projectors
1/01
EPSON PowerLite 5600p and 7600p Projectors - 5
Computer Video Port Pin Assignments
The Computer 1 analog port is a female video RGB, 15-pin
micro-D-style connector. Here are the pin assignments:
micro-D-style connector. Here are the pin assignments:
Positioning the Projector
Follow these guidelines to get the best results when projecting:
❏ Place the projector on a sturdy, level surface, between
❏ Place the projector on a sturdy, level surface, between
3.6 and 48 feet from the screen.
❏ Make sure there is plenty of space for ventilation around and
under the projector.
❏ Make sure the projector is within 6 feet of a grounded
electrical outlet or extension cord and within 5 feet of the
image source.
image source.
❏ Face the projector squarely toward the screen. Otherwise,
your image won’t be square.
Note: It’s easier to position the projector when the screen is
directly in front of the room. If the screen is placed diagonally in a
corner, it’s much more difficult to aim the projector squarely at
the screen and get a non-distorted image.
directly in front of the room. If the screen is placed diagonally in a
corner, it’s much more difficult to aim the projector squarely at
the screen and get a non-distorted image.
If you place the projector below the level of the screen, you’ll
have to tilt it up by extending the feet as shown. Tilting the
projector upward causes the image to lose its square shape, but
you can correct the distortion by pressing the
have to tilt it up by extending the feet as shown. Tilting the
projector upward causes the image to lose its square shape, but
you can correct the distortion by pressing the
Keystone
button as described on page 8.
If you place the projector level with the bottom of the screen,
the image will be square and you won’t have to adjust it. If
you place the projector higher than the bottom of the screen,
the image will still be square, but you won’t be able to fill the
whole screen with the image.
the image will be square and you won’t have to adjust it. If
you place the projector higher than the bottom of the screen,
the image will still be square, but you won’t be able to fill the
whole screen with the image.
HDTV480P (ANSI/
SMPTE)
SMPTE)
59.94
720
×
483
HDTV480P
(ATSC)
(ATSC)
59.94
704
×
480
HDTV480I (ANSI/
SMPTE)
SMPTE)
59.94
720
×
487
HDTV480I (ANSI/
SMPTE)
SMPTE)
59.94
1920
×
1080
HDTV480I
(ATSC)
(ATSC)
59.94
704
×
480
HDTV720P
(SMPTE)
(SMPTE)
59.94
1280
×
720
HDTV1080I (ANSI/
SMPTE)
SMPTE)
59.94
1920
×
1080
HDTV1080P (ANSI/
SMPTE)
SMPTE)
59.94
1920
×
1080
NTSC (SVGA)
60
800
×
438
NTSC (XGA)
60
1024
×
438
PAL (SVGA)
50
800
×
512
PAL (XGA)
50
1024
×
512
SECAM (SVGA)
50
800
×
512
SECAM (XGA)
50
1024
×
512
Pin #
Computer 1 port (analog)
1
Red video
2
Green video
3
Blue video
4
Monitor (ID bit 2)
5
GND
6
Red video GND
7
Green video GND
8
Blue video GND
9
+5V
10
Synchronous GND
11
Monitor (ID bit 0)
12
SDA
13
Horizontal sync
14
Vertical sync
15
Reserved
Mode
Refresh Rate (Hz)
Resolution
ideal
height
height