Epson 745c 제품 데이터시트
Epson PowerLite 745c Projector
8/04
Epson PowerLite 745c Projector
-
7
Using Direct Power On
The Direct Power On function enables faster setup. The
projector will start up automatically when you plug it in; you
won’t have to press the P
projector will start up automatically when you plug it in; you
won’t have to press the P
Power
button.
Follow these steps to enable Direct Power On:
1. Press the
Menu
button on the remote control and select the
Extended
menu.
2. Choose
Operation
and press
Enter
.
3. Choose
Direct Power On
and press
Enter
.
4. Highlight
ON
and press
Enter
.
5. Press
Esc
or
Menu
to exit.
Note:
When Direct Power On is enabled, shut down the projector as you
normally would. Follow the instructions in the next section. (The
projector will start automatically when power is restored after a
power failure if it is plugged in.)
When Direct Power On is enabled, shut down the projector as you
normally would. Follow the instructions in the next section. (The
projector will start automatically when power is restored after a
power failure if it is plugged in.)
Shutting Down the Projector
When you’ve finished using the projector, follow the
recommended procedure to shut it down. This extends the
lamp life and protects the projector from possible overheating.
recommended procedure to shut it down. This extends the
lamp life and protects the projector from possible overheating.
1. Turn off any equipment plugged into the projector.
2. To turn off the projector, press the P
Power
button on the
projector or remote control. You see a confirmation message.
(If you don’t want to turn it off, press any other button.)
(If you don’t want to turn it off, press any other button.)
3. Press the P
Power
button again. The P
Power
light flashes
orange as the projector cools down. When the projector
beeps twice, it’s safe to unplug it.
beeps twice, it’s safe to unplug it.
To turn the projector on again, wait until the P
Power
light
stops flashing. Then press the P
Power
button.
4. Press up on the blue foot release lever and lower the
projector to retract the front adjustable foot, as shown.
5. Replace the lens cap and unplug the power cord.
Caution
To avoid damaging the projector or lamp, never unplug the
power cord when the P
To avoid damaging the projector or lamp, never unplug the
power cord when the P
Power
light is green or flashing orange.
Using the Remote Control
Before using the remote control, insert the two AAA alkaline
batteries, as described on page 8.
batteries, as described on page 8.
When using the remote control, stand within 20 feet of the
projector. Point the remote control either at the projector or at
the screen (the projector’s front sensor can detect signals
bounced off the screen). Press the button for the function you
want to use.
projector. Point the remote control either at the projector or at
the screen (the projector’s front sensor can detect signals
bounced off the screen). Press the button for the function you
want to use.
Turning Off the Picture and Sound
You can use the
A/V Mute
button on the remote control to turn
off the image and sound. This is useful if you want to
temporarily redirect your audience’s attention.
❏ To turn off the picture and sound, press the
temporarily redirect your audience’s attention.
❏ To turn off the picture and sound, press the
A/V Mute
button. The screen turns blue.
❏ To turn the image and sound back on, press the
A/V Mute
button again.
You can create an image, such as a company logo or a picture, to
display on the screen whenever you press the
display on the screen whenever you press the
A/V Mute
button.
See the User’s Guide for more information.
Stopping Action
Press the
Freeze
button to stop the action in your video or
computer image and keep the current image on the screen. The
sound will continue.
sound will continue.
To restart the action, press the
Freeze
button again or
press
Esc
.
Zooming Your Image
Follow these steps to zoom in on a portion of the image:
1. Press the
E-Zoom
button on the remote control. You see
a crosshair indicating the center of the zoom-in area.
2. Use the
pointer button to position the crosshair in the
area you want to enlarge.
3. Continue pressing the
E-Zoom
button to enlarge the
selected area up to 4 times.