Epson cinema 550 제품 데이터시트
Epson PowerLite Cinema 550
8 - Epson PowerLite Cinema 550
11/05
Projector Status Lights
If your projector isn’t working correctly, first turn it off, wait for
the warning light to turn a steady orange, turn off the power
switch on the back, and unplug it. Then plug the power cord
back in and turn on the projector. If this doesn’t solve the
problem, check the lights on top of the projector. They alert
you to possible problems.
the warning light to turn a steady orange, turn off the power
switch on the back, and unplug it. Then plug the power cord
back in and turn on the projector. If this doesn’t solve the
problem, check the lights on top of the projector. They alert
you to possible problems.
Remote Control and IR Codes
Following is an illustration of the remote control, along with
the IR codes that correspond to the remote control buttons:
the IR codes that correspond to the remote control buttons:
Light
Status
Action
P
off
Make sure the power switch on the back of
the projector is turned on and the power cable
is connected securely at both ends.
the projector is turned on and the power cable
is connected securely at both ends.
P
orange
The projector is in standby mode. You can turn
off the power switch on the back to turn off
the projector or press the P Power button to
turn it on.
off the power switch on the back to turn off
the projector or press the P Power button to
turn it on.
P
flashing
green
green
The projector is warming up. Wait about
30 seconds for a picture to appear.
30 seconds for a picture to appear.
P
green
The projector is operating normally.
P
flashing
orange
orange
You’ve turned off the projector and it’s cooling
down. Wait until the light stops flashing, then
turn off the power switch in back (or press the
P
down. Wait until the light stops flashing, then
turn off the power switch in back (or press the
P
Power button to turn it back on).
flashing
orange
orange
High-speed cooling is in progress. If the
projector gets too hot again, projection stops
automatically. Make sure there is plenty of
space around and under the projector and
nothing is blocking the air filter. If it continues
to overheat, clean the air filter; see
instructions at right.
projector gets too hot again, projection stops
automatically. Make sure there is plenty of
space around and under the projector and
nothing is blocking the air filter. If it continues
to overheat, clean the air filter; see
instructions at right.
red
The projector is too hot and the lamp has
turned off. Wait 5 minutes, then turn it back
on. Make sure there is plenty of space around
and under the projector and nothing is
blocking the air filter. Clean or replace the air
filter if necessary.
If you are using the projector at an altitude
above 4900 feet, turn on High Altitude Mode.
turned off. Wait 5 minutes, then turn it back
on. Make sure there is plenty of space around
and under the projector and nothing is
blocking the air filter. Clean or replace the air
filter if necessary.
If you are using the projector at an altitude
above 4900 feet, turn on High Altitude Mode.
flashing red
(half-second
intervals)
(half-second
intervals)
The lamp needs to be replaced. Make sure
you have a spare lamp handy.
you have a spare lamp handy.
flashing red
at 1-second
intervals
at 1-second
intervals
There is an internal problem. Turn off the
power switch on the back of the projector and
unplug it. Then conatct Epson for assistance.
power switch on the back of the projector and
unplug it. Then conatct Epson for assistance.
Power light
Warning light
Function
Hex code
Power on
90h
Power off
91h
Memory
8Bh
Color Mode
8Fh
Menu
9Ah
Aspect
8Ah
Up
B0h
Down
B2h
Left
B3h
Right
B1h
Enter
85h
Esc
84h
HDMI
73h
D4/scart
7Eh
Input A
71h
Input B
9Dh
S-Video
9Ch
Video
70h
Contrast
2Ch
Color Temp.
2Dh
Skin Tone
2Ah
Pattern
96h
Blank
93h