Canon VB-M740E 매뉴얼

Network Camera

 / 

 

Installation Guide

Please be sure to read the “Safety Precautions” section for correct use. After reading this 
Installation Guide, keep it in a readily accessible location for future reference. 
* Some cameras are not available in certain countries or regions.

   Request a professional installer for all installation work. Never try to install the 

camera yourself. Doing so may result in unforeseen accidents such as dropping 

the camera or electric shock.

Camera, Screws (M4) x 4 

Template 

Installation Guide (This document) 

Setup CD-ROM 

Warranty Card 

Ceiling Plate 

Notice 

Dedicated wrench

Safety Wire, Screws (M3) x 1 

I/O Interface Cable (BK2-0035-000) 

Power Interface Cable 

 

 

Camera specific functions will be listed using the symbols below.

: VB-M741LE

   

: VB-M740E

The following accessories can be purchased separately as necessary. Some accessories are not 

available in certain countries or regions.

Dedicated accessory used to protect wiring cables that cannot be stored above the ceiling. This can 

be attached to the composite pipe.

Dedicated accessory used to install the camera to the end of pipe that extends from high ceilings, 

such as in big-box stores.

Dedicated AC adapter for this camera.

BIE-7155-000

© CANON INC. 2016 

Printed in Japan

2

7

12

11

18

3

4

1

6

8 9

10

13

5

14

15 16 17

Serial_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

MAC_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

1. Lens protector / 2. Screw hole for attaching / 3. LED (Orange) / 4. LED (Blue)* / 5. Notched cap / 
6. Power connection terminal 

 / 7. External device I/O terminals 

 / 

8. Audio input terminal (Black) (common LINE IN and MIC IN) 

 / 

9. Audio output terminal (White) (LINE OUT) 

 / 10. 100Base-TX LAN connector

11. Pan axis adjustment screw / 12. Tilt axis adjustment screw / 
13. Rotation axis adjustment screw / 14. Memory card slot / 15. Reset switch / 16. LED (Blue)* / 
17. Reboot switch / 18. Memory card cover
* On: when powered on, during reboot, during normal use / Off: when [Turn Off] is selected 

(please refer to the “Operation Guide”)

Unit: mm (in.)

Unit: mm (in.)

Camera mounting 
tab slots

Camera 
mounting tabs

111 (4.37)

102 (4.02)

60 (2.36) 60 (2.36)

60

 (2

.3

6)

60

 (2

.3

6)

96 (3.78)

214 (8.43)

288 (11.34)

85.7 (3-3/8) 

(*3, *4)

83.5 (3-9/32) 

(*4)

46.0 (1-13/16) 

(*4)

85.7 (3-3/8) 

(*3, *4)

83.5 (3-9/32) 

(*4)

46.0 (1-13/16) 

(*4)

14-  4.5 (0.18) 

(*5, *6)

7.0 (0.28)

151 (5.94)

142 (5.59)

Screw hole for attaching

4-M4 

(*1, *2)

4-M4 

(*7)

*1 Ceiling plate mount holes

*2 Option unit mount holes

*3 Ceiling/Wall mount holes position

*4 Junction box fixing holes position

*5 Ceiling/Wall mount holes

*6 Junction box fixing holes

*7 Camera mounting holes

Set the IP address and other network information on the camera using the “Camera Management 

Tool” on the Setup CD-ROM.

For details on how to operate the “Camera Management Tool”, please refer to the  “Camera 

Management Tool User Manual”.

Memory card slot

Loosen the screws with the dedicated wrench, open the 

memory card cover, and then place the memory card in 

the memory card slot. Once the memory card is in place, 

close the memory card cover and tighten the screws 

with the dedicated wrench.

To remove the memory card, push it in all the way until 

the card slightly pops out and remove.

 Important

•  Insert a memory card before installing the camera.
•  When using a memory card with the camera for the first 

time, it is recommended to format the card after inserting 
it into the camera (please refer to the “Operation Guide” > 
“Setting Page” > “Memory Card”).

•  Always unmount the memory card before removing it 

(please refer to the “Operation Guide” > “Setting Page” > 
“Memory Card”).

Once this has been completed, close the memory card cover and tighten the screws with the 

dedicated wrench.

     

Dedicated 

wrench

M4 × 4

Screws 

(included)

Use the dedicated wrench to adjust the 

following three rotation axes to set the angle.

 Note

Set the angle so that the memory card 
cover is at the bottom.

❶

❷

❸

❹

❺

❶

❷

❸

❹

 Note

Shake the unit after tightening the screws. If the joint 
section appears to wobble, further tighten the screw.

❶

❷

❸

When the installation has finished, please adjust the angle using the “Camera Angle Setting 
Tool”, found in the Setup CD-ROM.

When the unit is powered by a 24 V AC/ PoE+ power source, the heater unit can be used.
The heater unit’s orange LED will turn on, when the unit has been activated due to the low 

temperature within the camera, and the transfer of video is also not possible.  
Once the temperature within the camera has reached the level where it can transfer the video 

once again, the orange LED will turn off.

1 -1  

a

a

Ceiling Installation

Wall Installation

a.

 Template

1 -3  

b

b

b.

 Ceiling Plate

If the cables cannot be stored above the ceiling, 
such as with concrete ceilings, remove the notched 
cap at the camera joint section with the dedicated 
wrench, and create an opening for the cable to pass 
through.

The cables can be stored with the use of the conduit box 
CB740-VB (sold separately), which can also be attached 
to the composite pipe. Please refer to the installation guide 
included with the conduit box for the installation method.

Attach the ceiling plate to the junction box after confirming the 
fixing holes locations with the external dimensions diagram.

Mount using the Pendant Mounting Kit (sold separately).
For details please refer to the Installation Guide included with the kit.

1 -1  

Pass necessary cables for 
connecting the camera through 
the pipe.

 2.5 cm (1.0 in.)

❶

❹

❸

❷

M4* × 4

*  Included 

with Pendant 

Mounting Kit

M3*

           

c

❷

❸

❶

M3

Screws (included)

 Note

Pass the safety wire through 
the slit   and attach it to the 
hook on the rear side  .

Dedicated 

wrench

c. 

Safety wire 

d

e

d. 

I/O interface cable

e. 

Power interface cable

 Note

Completely wrap the cable connection with 
waterproof tape to the cable jacket, so as not 
to allow water to enter between the individual 
cables.

Notched 

cap

Dedicated 

wrench

The contents of this guide are subject to change without any prior notice.