Netgear FVS318v1 – Prosafe Wireless N VPN Firewall 설치 가이드
Start Here
Follow these instructions to set up your firewall.
Verify That Basic Requirements Are Met
Assure that the following requirements are met:
•
You have your broadband Internet service settings handy.
•
The computer is configured to obtain an IP address automatically via DHCP. For
instructions on how to do this, please see the animated tutorials on the ProSafe VPN
Firewall Resource CD or Appendix C in the Reference Manual on the ProSafe VPN
Firewall Resource CD.
instructions on how to do this, please see the animated tutorials on the ProSafe VPN
Firewall Resource CD or Appendix C in the Reference Manual on the ProSafe VPN
Firewall Resource CD.
First, Connect the Firewall to the Internet
1
1
Connect the Firewall
a.
Turn off your computer and cable or DSL broadband modem.
b.
Disconnect the Ethernet cable (A) which connects from your computer to the
cable or DSL broadband modem.
cable or DSL broadband modem.
c.
Securely insert the Ethernet cable from your cable or DSL broadband modem
into the Internet port (B) on the FVS318.
into the Internet port (B) on the FVS318.
d.
Securely insert one end of the Ethernet cable that came with your firewall into a
local port on the firewall such as local port 4 (C), and the other end into the
Ethernet port of your computer (D).
local port on the firewall such as local port 4 (C), and the other end into the
Ethernet port of your computer (D).
2
2
Restart Your Network in the Correct Sequence
Warning: Failure to restart your network in the correct sequence could prevent you
from connecting to the Internet.
from connecting to the Internet.
a.
First, turn on the cable or DSL broadband modem and wait 30 seconds for the
lights to stop blinking.
lights to stop blinking.
b.
Now, turn on your firewall.
c.
Last, turn on your computer.
Note: If software usually logs you in to the Internet, do not run that software or
cancel it if it starts automatically.
cancel it if it starts automatically.
d.
Check the status lights and verify the following:
•
Power: The power light is on. It goes on when your turn the firewall on.
•
Test: The test light is off. After turning on the firewall, the test light should
go off in less than a minute.
go off in less than a minute.
•
Internet: The Internet light on the firewall is lit. If the Internet light is not
lit, check that the Ethernet cable is securely attached to the firewall Internet
port and the powered on modem.
lit, check that the Ethernet cable is securely attached to the firewall Internet
port and the powered on modem.
•
Local: A local light is lit. If none are lit, check that the Ethernet cable to the
firewall from the powered on computer is securely attached at both.
firewall from the powered on computer is securely attached at both.
3
3
Log in to the Firewall
a. From your PC, launch your Internet browser.
b. Connect to the firewall by typing http://192.168.0.1 in the address field of
Internet Explorer or Netscape
®
Navigator.
c. Enter
admin for the firewall user name and password for the firewall password,
both in lower case letters.
d.
After logging in to the firewall, you will see the Internet Connection Setup
Wizard on the settings main page.
Wizard on the settings main page.
Installation Guide
Broadband Modem
12VDC 1.2A
8
7
6
5
4
3
2
1
LOCAL
10/100M
INTERNET
OFF
ON
ProSafe VPN Firewall FVS318
Broadband Modem
12VDC 1.2A
8
7
6
5
4
3
2
1
LOCAL
10/100M
INTERNET
OFF
ON
Broadband Modem
ProSafe VPN Firewall FVS318
Power
Test
Internet Port
Local Port 4
A
B
Internet Port
C
Local Port 4
D