Netgear WNHD3004 – RangeMax Wireless Access Point 설치 가이드

Installation Guide

T

This guide describes installation for the WNHD3004 3DHD Home Theater Adapter or the 
WNHDB3004 3DHD Wireless Home Theater Networking Kit. Learn more at 

1. Familiarize yourself with the features of the Wireless-N Adapter. 

The mode switch can be set to:
•

Auto – In Auto mode, the Wireless-N Adapter will automatically sense and set its 
own mode. It will run in AP mode if connected to a router or gateway. Otherwise, if 
connected to any other wired device(s), it will run in Bridge mode. (The Wireless-N 
Adapter is set to Auto mode from the factory.)

•

AP – In AP (access point) mode, the Wireless-N Adapter will act as an access point. 
In this mode, the Wireless-N Adapter should be connected to a router. 

•

Bridge – In Bridge mode, the Wireless-N Adapter is connected to your other wired 
device(s) and will connect wirelessly to the Wireless-N Adapter being used as an 
access point. NOTE: The unit running in Bridge mode can only connect to the 
WNHD3004 Access Point.

2. Verify that:

•

You have Broadband Internet access through a powered-on router or gateway.

•

You are connecting Ethernet-enabled devices, such as a network-enabled game 
console (an XBox 360 or Sony PS3), a digital media player (an Apple TV or 
NETGEAR Digital Entertainer), an IPTV set-top box, or a personal computer.

1. Set the switch on the back of each Wireless-N Adapter to Auto mode.

Caution: Do not plug in the power adapter before step 2.

2. Connect the Ethernet cable from a LAN port in the router or gateway (A) to an Ethernet 

port on one Wireless-N Adapter. 

3. Place the other Wireless-N Adapter near the media player, game console, or set-top box 

(B), and connect it with an Ethernet cable.

4. To complete installation, connect a power adapter to the Wireless-N Adapter(s). Allow 

a few minutes for your devices to connect to the Internet. If you are not connected, see 
“Troubleshooting” on page 2.

Note: By following the steps in this installation with both Wireless-N Adapter units set to 
Auto mode, the Wireless-N Adapter connected to your router has set itself to AP mode, 
while the second Wireless-N Adapter is set to Bridge mode.

1. Make sure the 3DHD Home Theater Adapter you are adding is not set to AP mode, 

place it near the devices that will work with it.

2. Connect a power adapter to the new Wireless-N Adapter.

The power light should blink in green.

3. On the new Wireless-N Adapter, press the WPS button once (located on the front 

panel). Its WPS light should start to blink.

4. Within 2 minutes, press the WPS button on the Wireless Access Point (the one 

connected to the router). Its WPS light should start to blink.

5. After 1-2 minutes the new Wireless-N Adapter in Bridge mode should be associated 

with the Wireless Access Point. The power lights on both units will be solid green.

By default, the IP address is assigned dynamically by the router. Without a router, the IP 
address of the Wireless-N Adapter in AP mode will default to 192.168.1.240 and the IP 
address of the Wireless-N Adapter in bridge mode will default to 192.168.1.241. 
Configuring the Wireless-N Adapter to use a fixed or dynamic IP address lets you access 
the Wireless-N Adapter configuration from a Web browser.

1. Connect an Ethernet cable from your PC to an Ethernet port on the Wireless-N Adapter.

2. Browse to http://www.mywifiext.com. NOTE: If this does not work, you can get the 

AP or Bridge’s IP from your router, and browse to its IP address.

3. Enter the username admin and the password password at the prompt to log in. 

For more information on configuring, refer to the 3DHD Home Theater Adapter User 
Manual. You can download it from 

Digital set-top box

Network TV 
viewer/DVR

DMA

Gaming console

WNHDB3004

Network storage

Router/gateway

Desktop PC

Internet