Netgear MoCA Coax-Ethernet Adapter 설치 가이드

This symbol was placed in accordance with the European Union Directive 2002/96 on 
the Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of 
within the European Union, this product should be treated and recycled in accordance 
with the laws of your jurisdiction implementing the WEEE Directive.

©2008 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered 
trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and product 
names are trademarks or registered trademarks of their respective holders. Information is subject to 
change without notice. 

2.  Connect the second MCA1001 Coax-Ethernet Adapter according to the sequence of 

steps below. You can attach a number of peripheral devices following these steps. For 
instructions on adding other devices, including a NETGEAR switch, refer to the User 
Manual on the Resource CD.

When you have finished this step, your MoCA adapter and peripheral devices should 
be connected as shown.

Connect an Ethernet cable from the LAN port on the MoCA adapter to a LAN 
port on your gaming console, similar to step 1.a. above.

Connect the Coax IN cable from the cable wall outlet to the Coax IN connection 
on the MoCA adapter, similar to step 1.c. above.

MCA1001

TV

Gaming 
console

Set-top box

Coax IN
Coax OUT
Ethernet cable
HDMI cable

Connect the provided coax cable from the MoCA adapter Coax OUT connection 
(by hand, finger-tight) to the Coax IN connection on the set-top box.

Connect your gaming console and set-top box to your TV, using an HDMI cable 
(or similar).

Connect power to the MoCA adapter and verify status of the LEDs, as in steps 
1.e. and 1.f., above.

Power LED is off.

• Make sure that power is supplied to the electrical outlet if it is 

controlled by a wall switch.

• Make sure that the LEDs are activated (LED Off/On button in out 

position).

Coax traffic LED
is off.

• Make sure that the LEDs are activated (LED Off/On button in out 

position).

• Make sure that the Mode button is set to Normal (Mode LED is off, 

Mode button in out position) for all MoCA adapters on the network. 
When the Mode button is set to Configuration (Mode LED is solid, 
Mode button in), no traffic is being transmitted.

• Make sure that all cables are connected (coax cables should be 

connected snugly, finger-tight) and that your coax connection is 
working. Loose coax connections can interfere with your cable 
service as well as the performance of the MoCA adapters.

• If security was set, make sure you have set the same security on all 

MoCA adapters (see the User Manual on the Resource CD).

• Try restarting each MoCA adapter by pressing its reset button (less 

than 10 seconds).

• Try resetting each MoCA adapter to its factory default settings by 

pressing the reset button (longer than 10 seconds).

Interference is 
occurring for 
some TV 
channels

• Make sure that power is supplied to all MoCA adapters in your 

network.

• Make sure that all cables are connected (coax cables should be 

connected snugly, finger-tight) and that your coax connection is 
working.

• Configure the MoCA adapter to a different channel using the 

MCA1001 Configuration Utility (see the User Manual on the 
Resource CD).

Thank you for selecting NETGEAR products. After completing installation, register your 
product at http://www.NETGEAR.com/register. 

Registration on the website or over the phone is required before you can use our telephone 
support service. The phone numbers for worldwide regional customer support centers are 
on the Warranty and Support Information card that came with your product. 

Go to http://www.NETGEAR.com/support for product updates and Web support.