KitchenAid 4.1 cu. ft. Thermal Oven 설치 가이드
To get the most efficient use
from your new oven, read your
Use and Care Guide. Keep Installation
Instructions
and Guide close to oven
for easy reference.
This oven is manufactured with white (neutral)
power supply wire and a cabinet-connected bare
grounding wire twisted together.
power supply wire and a cabinet-connected bare
grounding wire twisted together.
4.
Feed oven cable through opening in
the cabinet. Make electrical connection
the cabinet. Make electrical connection
following the steps needed for your installation.
1. Disconnect the power supply.
2. Remove the junction box cover.
3. Connect oven cable to junction box through the
1. Disconnect the power supply.
2. Remove the junction box cover.
3. Connect oven cable to junction box through the
U.L.-listed conduit connector.
4. Connect the two black wires together with
twist-on connectors.
5. Connect the two red wires together with
twist-on connectors.
6. Complete electrical connection according to
local codes and ordinances.
Figure 1
junction
box
box
red
wires
wires
white
wire
wire
white and bare
grounding oven
cable wires —
factory crimped
grounding oven
cable wires —
factory crimped
cable from
power supply
power supply
black
wires
wires
cable from
oven
oven
U.L.-listed
conduit
connector
conduit
connector
Figure 2
cable from
power supply
power supply
cable from
oven
oven
junction
box
box
U.L.-listed conduit
connector
connector
red
wires
wires
white
wires
wires
black wires
bare grounding
wires
wires
If local codes PERMIT
connecting cabinet-grounding
conductor to neutral white
wire in junction box:
If local codes DO NOT PERMIT
connecting cabinet-grounding
connecting cabinet-grounding
conductor to neutral white
wire in junction box:
If connecting to a
four-wire electrical system:
7. Connect the factory-crimped
bare and white oven cable wires
to the neutral (white) wire in
junction box. See Figure 1.
to the neutral (white) wire in
junction box. See Figure 1.
8. Replace junction box cover.
7. Separate the factory-crimped
bare and white oven cable wires.
8. Connect white oven cable wire to
neutral (white) wire in junction
box. See Figure 2.
box. See Figure 2.
9. Connect the bare grounding
oven cable wire to a grounded
wire in the junction box. See
Figure 2.
wire in the junction box. See
Figure 2.
10. Replace junction box cover.
7. Separate bare and white oven
cable wires.
8. Connect white oven cable wire
to neutral (white) wire in
junction box. See Figure 2.
junction box. See Figure 2.
9. Connect the bare grounding
oven cable wire to the green
grounding wire in junction box.
Do Not connect bare grounding
wire to neutral (white) wire in
junction box. See Figure 2.
grounding wire in junction box.
Do Not connect bare grounding
wire to neutral (white) wire in
junction box. See Figure 2.
10. Replace junction box cover.
Carefully push against seal area of oven front
frame when pushing oven into cabinet.
Do Not push against outside edges.
frame when pushing oven into cabinet.
Do Not push against outside edges.
Page 3
10.
Turn on power supply. The display
panel will light up briefly. “PF” should appear in
the temperature display.
the temperature display.
11.
Check the operation of your single oven.
Press the “BROIL” pad. “BROIL” will appear in
Press the “BROIL” pad. “BROIL” will appear in
Electrical connection
B
Attachment
C
Check operation
D
5.
Lift oven into cabinet cutout using the
oven opening as an area to grip.
Push against seal area of front frame to push
oven into cabinet until shipping feet almost
contact cabinet. Use a Phillips screwdriver to
remove screws attaching shipping feet. Remove
and discard shipping feet.
Push oven completely into cabinet and center
oven in cabinet cutout.
oven into cabinet until shipping feet almost
contact cabinet. Use a Phillips screwdriver to
remove screws attaching shipping feet. Remove
and discard shipping feet.
Push oven completely into cabinet and center
oven in cabinet cutout.
8.
Replace oven racks.
Push trim
into place.
Replace
trim screw.
into place.
Replace
trim screw.
4 screws
Slide top
of trim up.
of trim up.
BAKE
BROIL
CLEAN
the display. Press the “START” pad. Make sure the
oven door is closed and the “ON” light is shown in
the display area. After 2 minutes, partially open
oven door. You should feel heat from the oven.
Press the “CANCEL” pad.
Check the operation of your double oven.
Press the “Upper Oven” pad. Press the “BROIL”
pad. “BROIL” will appear in the display. Press the
“START” pad. Make sure the oven door is closed
and the “ON” light is shown in the display area.
After 2 minutes, partially open oven door. You
should feel heat from the oven. Press the
“CANCEL” pad.
Press the “Lower Oven” pad and repeat the steps
you completed for checking the upper oven.
oven door is closed and the “ON” light is shown in
the display area. After 2 minutes, partially open
oven door. You should feel heat from the oven.
Press the “CANCEL” pad.
Check the operation of your double oven.
Press the “Upper Oven” pad. Press the “BROIL”
pad. “BROIL” will appear in the display. Press the
“START” pad. Make sure the oven door is closed
and the “ON” light is shown in the display area.
After 2 minutes, partially open oven door. You
should feel heat from the oven. Press the
“CANCEL” pad.
Press the “Lower Oven” pad and repeat the steps
you completed for checking the upper oven.
If your oven does not heat or an “F”, followed by
a number, appears in the display, contact your
dealer or check the “If you need service...” section
of this Installation Instructions.
a number, appears in the display, contact your
dealer or check the “If you need service...” section
of this Installation Instructions.
shipping
foot
foot
6.
Important: Securely fasten oven to cabinet
using the screws provided (two screws for a single
oven or four screws for a double oven). Insert the
screws through holes in mounting rails. Do Not
overtighten screws.
oven or four screws for a double oven). Insert the
screws through holes in mounting rails. Do Not
overtighten screws.
Important: Replace the door with the model/serial
rating plate on the upper oven.
rating plate on the upper oven.
On some models, the construction of this door is
designed to withstand self-cleaning temperatures.
designed to withstand self-cleaning temperatures.
7.
Slide top end of each trim upward onto oven
side rails. Push each trim into place at bottom of
trim. Use screws to attach each trim to oven. Take
care not to scratch other surfaces with ends of trim.
trim. Use screws to attach each trim to oven. Take
care not to scratch other surfaces with ends of trim.
Electrical Shock Hazard
Turn power supply off before connecting wires.
Use 8 gauge solid copper wire.
Electrically ground range.
Failure to follow these instructions can result
in death, fire, or electrical shock.
in death, fire, or electrical shock.
WARNING
If your house has aluminum wiring, see
“Electrical requirements”, Page 2.
“Electrical requirements”, Page 2.
9.
Reinstall the oven door by inserting ends
of hinges into hinge slots in the oven frame. Push
hinges in as far as they will go. Open the door
(you will feel the door drop into place) and rotate
both hinge latches back to the locked position.
hinges in as far as they will go. Open the door
(you will feel the door drop into place) and rotate
both hinge latches back to the locked position.
Close and open the door to check that the door
closes and opens completely. If door does not
close or open completely, repeat the door
removal step and reinstall door as described
above.
closes and opens completely. If door does not
close or open completely, repeat the door
removal step and reinstall door as described
above.
Repeat for lower oven door.