Craftsman PP1802U 사용자 설명서

OPERATION cont.

RUNNING YOUR POLISHER AND

WAXING TOOL cont.
3. Place the extension cord over your shoulder

to keep it safely out of your way (see Fig. 6).
4.

Power ON/OFF:

- To start operation, press

Locking (On/Off)

Push Button (1) forward and at same

time pull up on

Release On/Off Trigger

Switch (2) (See Fig. 7).

Release both button and switch to lock tool

on for continuous use.
- To stop operation, again press Push Button

forward and at same time pull up and

release the trigger switch (See Fig. 7).
5. Apply wax in a straight line with either a

side-to-side or back and forth motion.

ALWAYS use broad, even strokes when

applying wax (See Fig. 8).

VARIABLE SPEED CONTROL (SEE FIG. 9)
The convenient Variable Speed Control dial
allows you to increase or decrease the polishing
speed. Rotate the dial with your thumb to choose
one of the 7 speeds: The higher the number
the faster the speed.

REAR TWIST HANDLE (SEE FIG.10)
For polishing control and added comfort, the

polisher is equipped with a rear rotatable handle.

Push in the

Locking Push Button on the

rotatable handle and you can rotate the

handle 90° to left or right. Then release the

locking button. A click will be heard when the

handle is fully locked in place.

RUNNING YOUR POLISHER AND

WAXING TOOL cont.

(1)

(2)

Fig. 7

Fig. 9

Fig. 10

Fig. 6

Fig. 8

Locking Push Button

Dial Indication

MIN

1
2
3
4
5

MAX

Speed range (/min)

800

1100
1500
1800
2500
2800
3000

Type of works

For waxing

For polishing

MAINTENANCE

TO REPLACE THE BRUSHES (SEE FIG. 11)

1. Use a slotted screwdriver to remove cap and brush holder by turning left to loosen

cap and right to tighten.
2. Check the length of the brush and replace if under 1/4 - in. (7mm).
3. Put the brush holder into the body.

Tighten the brush holder.
4. Check the polisher is working properly

before use; allow it run for a few minutes

to enable the brushes to be stable.
NOTE: When brushes need replacement

always renew both brushes, even if one is

still more than 1/4-in. (7mm).
NOTE: Brushes can be purchased at a Sears Parts & Repair Service Center

or online at www.craftsman.com. See pages 16-17 for item part number.

Fig. 11

WARNING: Make sure the handle is in the locked position before turning on the

polisher. Rotating the handle is permitted only in the switched off condition.

WARNING: ALWAYS remove the plug from the socket before carrying out any

adjustment, servicing or maintenance.

CARE & CLEANING

1. We recommend hand washing and air drying for longer foam pad life. Pads should be

cleaned with a mild dish washing detergent. Rinse pads to remove all soap.
2. Remove the foam pad when the polisher is not is use, so the pad can dry out

and retain its original shape.
3. To prolong the life of the pad,

ALWAYS store the polisher with the pad face up.

NEVER USE ABRASIVE COMPOUNDS WITH THIS TOOL.

DO NOT apply too much wax to the foam pad.

Applying too much wax causes the foam pad to become saturated and it will not last

as long.

THIS MAKES POLISHING MORE DIFFICULT AND IT TAKES LONGER.

6. If the foam pad has large vibration, you may be using too much wax.
7.

ONLY USE a mild soap solution and a damp sponge to clean the polisher.

DO NOT immerse any part of the polisher in liquid.

NOTE: Your buffer/polisher requires no additional lubrication or maintenance. Never use water or

chemical cleaners to clean your buffer/polisher. If the supply cord is damaged, it must be replaced

by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.