Fujifilm Uvijet KA 제품 데이터시트
Pre-production Tests
Uvijet KA ink is formulated to give excellent adhesion to
most major brands of plastic, polypropylene and
polyethylene materials. Polyolefin’s should have a
surface energy level of 42 dynes/cm or higher.
most major brands of plastic, polypropylene and
polyethylene materials. Polyolefin’s should have a
surface energy level of 42 dynes/cm or higher.
However it is strongly recommended that all substrates
are tested before a commercial run. For information on
adhesion promoters refer to the Uvijet Fusion Primer
range.
are tested before a commercial run. For information on
adhesion promoters refer to the Uvijet Fusion Primer
range.
Plastics
Some plastic substrates may contain lubricants which,
like plasticisers, may impair adhesion and block
resistance for a considerable time after printing.
like plasticisers, may impair adhesion and block
resistance for a considerable time after printing.
There may also be residues from glues and adhesives
used on backing sheets. This can be overcome by
wiping the surface with isopropyl alcohol (IPA) before
printing.
used on backing sheets. This can be overcome by
wiping the surface with isopropyl alcohol (IPA) before
printing.
To reduce the risk of problems generated by the build-
up of static electricity it is advisable to pass an earthed
anti-static brush over the material prior to printing. Allow
static generated from protective sheets to dissipate
before printing. Ensure that the printer is cited as per
recommended humidity/temperature recommendations
40-70% RH, 18-30
up of static electricity it is advisable to pass an earthed
anti-static brush over the material prior to printing. Allow
static generated from protective sheets to dissipate
before printing. Ensure that the printer is cited as per
recommended humidity/temperature recommendations
40-70% RH, 18-30
o
C.
Chemical and Abrasion Resistance
Uvijet KA inks have good chemical and abrasion
resistance.
resistance.
Outdoor Use
Accelerated weathering tests have been carried out in a
Xenon Arc Weatherometer set to the SAEJ 1960
Standard. Under these conditions the accelerated
weathering of Uvijet KA inks equates to approximately
24 months outdoor exposure in a temperate climate
such as Northern Europe.
Xenon Arc Weatherometer set to the SAEJ 1960
Standard. Under these conditions the accelerated
weathering of Uvijet KA inks equates to approximately
24 months outdoor exposure in a temperate climate
such as Northern Europe.
Storage
Uvijet KA ink should not be stored in direct sunlight or
near heat sources and should be kept away from
peroxides. For optimum shelf-life, products should be
stored at moderate temperatures between 5
near heat sources and should be kept away from
peroxides. For optimum shelf-life, products should be
stored at moderate temperatures between 5
o
C and
30
o
C. Storage outside of these temperatures may lead
to deterioration in the performance of the products.
When stored in a cool environment the inks are
expected to have a shelf-life of 12 months from date of
manufacture.
expected to have a shelf-life of 12 months from date of
manufacture.
Fujifilm Speciality Ink Systems Limited:
• Has certification to the International Environmental
Standard ISO 14001.
• Is committed to minimising the risk to users of our
products, and also to minimising the impact of our
activities on the environment, from formulation
through to production and supply.
activities on the environment, from formulation
through to production and supply.
• Research and development team , work to an in
house Health Safety and Environmental policy,
termed ‘Design for Health, Safety and Environment’,
with the aim of proactively developing products with
the least impact on health, safety and the
environment.
termed ‘Design for Health, Safety and Environment’,
with the aim of proactively developing products with
the least impact on health, safety and the
environment.
• Regularly review and monitor our impacts and
activities, setting objectives and targets as part of a
continual improvement process.
continual improvement process.
• Is committed to reducing waste through better use
of raw materials, energy, water, re-use and
recycling.
recycling.
Safety and Handling
Uvijet KA Inks:
• Have a flash point greater than 55
o
C and are
therefore not classified as ‘dangerous substance’
under the Dangerous Substances and Explosive
Atmospheres Regulations (DSEAR).
under the Dangerous Substances and Explosive
Atmospheres Regulations (DSEAR).
Comprehensive information on the safety and handling
of Uvijet inks is given in the appropriate Safety Data
Sheets.
of Uvijet inks is given in the appropriate Safety Data
Sheets.
Environmental Information
Uvijet KA Inks:
• Do not contain ozone-depleting chemicals as
described in the Montreal Convention.
• Are formulated free from aromatic hydrocarbons.
• Are free from any volatile solvent and can therefore
• Are free from any volatile solvent and can therefore
be considered to have less impact on the
environment when compared to solvent-based
products.
environment when compared to solvent-based
products.
The information and recommendations contained in this Product Information sheet, as well as technical advice otherwise given by representatives of Fujifilm Speciality Ink
Systems Limited and its associated companies, whether verbally or in writing, are based on our present knowledge and believed to be accurate. However, no guarantee
regarding their accuracy is given as we cannot cover or anticipate every possible application of our products and because manufacturing methods, printing stocks and other
materials vary. For the same reason our products are sold without warranty and on condition that users shall make their own tests to satisfy themselves that they will meet fully
their particular requirements. Our policy of continuous product improvement might make some of the information contained in this Product Information sheet out of date and
users are requested to ensure that they follow current recommendations.
Systems Limited and its associated companies, whether verbally or in writing, are based on our present knowledge and believed to be accurate. However, no guarantee
regarding their accuracy is given as we cannot cover or anticipate every possible application of our products and because manufacturing methods, printing stocks and other
materials vary. For the same reason our products are sold without warranty and on condition that users shall make their own tests to satisfy themselves that they will meet fully
their particular requirements. Our policy of continuous product improvement might make some of the information contained in this Product Information sheet out of date and
users are requested to ensure that they follow current recommendations.
FUJIFILM SPECIALITY INK SYSTEMS LIMITED
Pysons Road, Broadstairs
Kent CT10 2LE
United Kingdom
T: +44 (0)1843 866668
F: +44 (0)1843 872184
www.fujifilm.eu
3152/
O
1
3